Pioneer VSX-D810S - Manual (Page 27)

27
En
Sound Modes
Switching ANALOG/DIGITAL
Signal Input
When you select a function (for example CD) that is
only hooked up by a digital connection, then the
ANALOG/DIGITAL signal input switch will automati-
cally choose digital (VSX-D810S only). If you have that
function hooked up by both digital and analog connec-
tions this switch lets you choose which to listen to.
Playing Sources with Dolby
Digital or DTS Sound
1 Turn on the power of the playback component.
2 Turn on the power of the receiver.
Be sure that the STANDBY indicator turns off on the
front panel.
3 Press MULTI CONTROL buttons or the
FUNCTION button to select the source you
want to playback.
If the DIRECT FUNCTION is off you have to use the
FUNCTION button to select the source (see p.40).
4 Press RCV.
5 Press SIGNAL SELECT to select DIGITAL.
(Refer to “Switching ANALOG/DIGITAL signal input”
on this page.)
6 Press 2/DTS to switch the 2/DTS mode
on.
7 Start playback of the component you se-
lected in step 1.
8 Press MASTER VOLUME (+/–) to adjust the
volume level.
MEMO:
• You can only hear the sound on DTS encoded discs if
the CD or LD player with DTS is digitally connected
to this receiver. If you play a DTS encoded disc
through analog connections you will only hear digital
noise, not the soundtrack. To prevent noise, you need
to make digital connections (Refer to page 5-6) and
set SIGNAL SELECT to DIGITAL.
1 Press RCV.
2 Press SIGNAL SELECT to select the input
signal corresponding to the source component.
Each press switches between ANALOG and DIGITAL
signal selection (VSX-D710S).
On the VSX-D810S receiver there is an AUTO setting
(see page 22 #
1 ). In this setting the receiver will
automatically switch between the analog and digital
signals according to what is being input. If both
signals are input the AUTO setting will choose the
digital one. This setting is convenient as the receiver
will always choose the best or appropriate signal.
3 While SIGNAL SELECT is set to DIGITAL,
2 DIGITAL lights when a Dolby Digital
signal is input, DTS lights when a DTS signal
is input.
MEMO:
• SIGNAL SELECT is fixed in the ANALOG position
for components not assigned to one of the digital
input jacks.
• This receiver can only play back Dolby Digital, PCM
(32kHz, 44kHz, and 48kHz [VSX-D810S can play
96kHz]), and DTS, digital signal formats. With digital
signal formats other than these, set SIGNAL SELECT
to ANALOG.
• When an LD or CD player compatible with DTS is
played back with SIGNAL SELECT set in “ANALOG”,
digital noise is output caused by playing back the DTS
directly (no decoding). To prevent noise, you need to
make digital connections (Refer to page 6) and set
SIGNAL SELECT to “DIGITAL”.
• Some DVD players don’t output DTS signals. For
more details, refer to the instruction manual supplied
with your DVD player.
5
8
2
6
3
2
DISC
MPX
DISPLAY RF ATT
D.ACCESS
CLASS
ATT
BAND
/DTS DSP TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
1 ¡ 4 ¢
7 8 3 ¶
EFFECT
DVD VCR CD-R TV
RCV TUN TVC CD
MIDNIGHT
LOUDNESS MUTING SETUP FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER SOURCE
1 2 3
4 5 6
7 8
10
9
0
2
TV
TVFUNC
MENU
VOLUME MASTER VOLUME
TV CONTROL
CHANNEL
ENTER
DISC
MPX
DISPLAY RF ATT
D.ACCESS
ST
TUNE
TUNE
ST
CLASS
ATT
BAND
/DTS DSP TEST TONE
CH SELECT CH LEVEL FUNCTION
SIGNAL SELECT
1 ¡ 4 ¢
7 8 3 ¶
EFFECT
DVD VCR CD-R TV
RCV TUN TVC CD
MIDNIGHT
LOUDNESS MUTING SETUP FL DIMMER
MULTI CONTROL
5.1 / 7.1
RECEIVER SOURCE
1 2 3
4 5 6
7 8
10
9
0
2 1
4