Pioneer VSX-D810S - Manual (Page 22)

22
En
Displays & Controls
& MEMORY button (see page 31-32)
Press to memorize a station for recall using the
STATION (+/–) buttons.
* CLASS button (see pages 31-32)
Switches between the three banks (classes) of station
memories.
( RF ATT button (see page 30)
Use to lower the input level of a radio signal that is
too powerful or contains interference thus causing the
receiver to distort
Display
1 SIGNAL SELECT indicators
Light to indicate the type of input signal assigned for
the current component (see “Front Panel“, 0
SIGNAL SELECT). When the AUTO setting is being
used on the VSX-D810S receiver a set of brackets will
appear around the SIGNAL SELECT indicators.
2
DIGITAL : Lights when a Dolby Digital signal is
played.
DTS : Lights when a source with DTS audio signals is
played.
ANALOG : Lights when an analog signal is selected.
DIGITAL : Lights when a digital audio signal is
selected.
[ ]: Lights when the AUTO setting is selected. (VSX-
D810S only)
2 DTS indicator
Lights when DTS mode is being used.
3 2 DIGITAL indicator
When the 2 (DOLBY)/DTS mode of the receiver is
on, this lights to indicate playback of a Dolby Digital
signal. However, 2
PRO LOGIC lights during two
channel playback of Dolby Digital.
4 Surround Back indicator (VSX-D810S only)
Lights when most Surround Back channel flag encoded
(6.1channel) software is playing. (With some Surround
Back channel software the surround back indicator
won’t light because there is no flag encoded in the
software.) If you play DTS 5.1/6.1 channel software
surround sound will be heard whether it is encoded
with a surround back channel flag or not.
5 OVERLOAD indicator
This lights when an analog signal is too high (the
SIGNAL SELECT would have to be on ANALOG). It
indicates the sound is distorting and the input signal
should be reduced.
6 ATT indicator
Lights when ATT is used to attenuate (reduce) the
level of the input signal (can only be used in ANA-
LOG mode).
7 DIRECT indicator
Lights when source DIRECT is in use. This function
bypasses all tone, balance, DSP and Dolby Surround
effects.
8 SPEAKER indicator
Shows if the speaker system is on or not. SP
3A
means that speakers are switched on. SP
3 means
that speakers are switched off.
9 MONITOR indicator
Lights when MONITOR is selected. Used to hear a
recording as it's being made (see page 36).
0 RF ATT indicator
Lights when the RF ATT is on (see p. 30).
- EON indicator
The box around EON indicator lights to inform you
that the currently tuned station carries the EON data
service. When the EON mode is set, the
EON
indicator light’s, but during actual reception of an
EON broadcast the
EON indicator will flash. An
empty box in the EON indicator spot means it is
possible to pick up an EON broadcast but the
receiver has not been set to do so (this will only
appear when RDS is switched on).
= RDS indicator
Lights when an RDS broadcast is received.
dB
SIGNAL SELECT
MIDNIGHT
LOUDNESS
DIRECT MONITOR
TUNED
MONO ANALOG DIGITAL
SP A DIGITAL DTS
DIGITAL
PRO LOGIC
SB ATT
DSP
DNR
RF ATT EON
STEREO RDS
1 2 3 4 5 6 7 8 9 0 - =
~ & ! # $ @ % ^
CHARACTER/SEARCH button (see pages 32, 34)
Use to search for different program types in RDS
mode. It is also used to input station names.
EON MODE button (see pages 35)
Use to search for different programs that are transmit-
ting traffic or news information (this search method is
called EON).
) PHONES jack
Use to connect headphones but this does not switch
the speakers off.