ADTRAN ISU 128 - Manual (Page 42)

Chapter 6: Configuration
1 ISU 128 User Manual 27
Configur
2=DTE options
1=Netw. options
1=Asynchronous
2=Synchronous
G
3=Protocol 1=Clear Channel
2=BONDING mode 1
3=V.120
4=V.34
5=V.110
6=DSU 57.6 ASYNC
7=T-LINK
8=SAP .
9=FALLBACK 1=Fallback Def
0=PPP asyn-sync
4=Quick setup
S ‘Buffer Display’
1=Loopback DTE
2=Loopback Netw.
3=Loopback Proto
4=Loopback Remote
5=Test Remote
6=Lpbk Disable
7=NEBE/FEBE
8=Software Ver
1=No Rem Lpbks
2=DDS Accepted
3=V54 Accepted
4=DDS + V54 Accept
1=Hang up line
2=Dial number
3=Redial last #
4=Answer Call
5=Dial Stored #
6=Store/Review #
1=Dial 56K sync
2=Dial 64Ksync
3=Dial 112K sync
4=Dial 128K sync
5=Dial PPP
6=V.34 1152 async
7=Dial 57.6 asyn
8=Dial 115.2 asy
9=Fallback 57.6k
0=More
1=Dial Line
2=Leased Line
1=Switch protocl
2=Call type
1=AT&T 5ESS
2= DMS-100
3=National ISDN1
4=NEC Switch
1=Speech
2=Audio
3=Data 56Kbps
4=Data 64Kbps
3=Terminal ID Set SPID
Set LDN
4=Dial options 1=Front Panel
2=RS-366
3=AT commands
4=V.25
5=Disabled
5=Auto answer 1=Disabled
2=Enabled
3=Dump all calls
6=Answer tone 1=No answer tone
2=Incoming tone
3=Outgoing tone
4=Always tone
7=Connect Timout 1=15 sec
2=30 sec (def)
3=1 minute
4=2 minute
5=4 minute
8=Call Screening 1=Answer any
2=ansr if SNO…9
1=Clock mode 1=Slave
2=Master
2=Channel rate 1=64k
2=128k
1=TXINIT
2=TXFA
3=TXADD01
4=TXDEQ
5=TANULL
6=TCID
1=Error Ctrl
2=Compression
3=MNP Blk Size
1=Leased 128k
2=Ldm 128 Master
3=TBD
4=TBD
5=TBD
6=TBD
7=TBD
1=1 sec or EON
2=2 sec or EON
3=5 sec (default)
4=10 sec or EON
5=20 sec or EON
6=Wait for EON
1=V.25 HDLC
2=V.25 ASYNC
3=V.25 BISYNC
4=V.25 HDLC FLAG
1=2400
2=4800
3=9600
4=19200
5=38400
1=Normal
2=External
6=48000
7=56000
8=64000
9=112000
0=128000 1=Bit Rate
2=Connector Type 1=RS-530
2=V.35
3=RS-232
3=RTS Options 1=1 Ms delay
2=18 Ms delay
4=CTS Options 1=Forced CTS
2=Follows RTS
5=CD Options 1=CD Forced on
2=Normal
3=Off with LOCD
4=Off with Link Down
6=DTR Options 1=Ignore DTR
2=Cmd when Off
3=Idle when Off
4=Off>On dial #0
5=Dial #0 if On
6=Answer if On
7=Dial/Ans if On
7=DSR Options 1=DSR forced on
2=OFF Idle+Test
3=OFF Link Down
8=Transmit Clock
1=300
2=1200
3=2400
4=4800
5=9600 1=Bit Rate
2=Connector Type 1=RS-530
2=V.35
3=RS-232
3=RTS Options 1=1 Ms delay
2=18 Ms delay
4=CTS Options 1=Forced CTS
2=Follows RTS
5=CD Options 1= CD Forced on
2=Normal
3=Off with LOCD
4=Off with Link Down
6=DTR Options 1=Ignore DTR
2=Cmd when Off
3=Idle when Off
4=Off>On dial #0
5=Dial #0 if On
6=Answer if On
7=Dial/Ans if On
7=DSR Options 1=DSR forced on
2=OFF Idle+Test
3=OFF Link Down
8=Flow Control
9=Data Format 1=Data Bits 1=8 Data Bits
2=7 Data Bits
1=None
2=Odd
3=Even
1=1 Stop bit
2=1.5 Stop bits
3=2 Stop Bits
1=Hardware Flow
2=Software Flow
3=No Flow Ctrl
6=19200
7=38400
8=57600
9=115200
2=Parity Bits
3=Stop Bits
1=PPP
2=Multilink PPP
3=PPP w/Comp
1=Method
2=TBD
1=No Compression
2=Compress MNP5
3=Compress V42
4=Comp V42/MNP5
1=Normal
2=Direct
3=Reliable MNP
4=Auto-Rel MNP
5=Force LAPM
6=Force MNP
1=64 bytes
2=128 bytes
3=192 bytes
4=256 bytes
5=Remote config 1=Cfg. Rmt. Unit
2=Set Password
3=Loopback remote 1B
4=Loopback remote 2B
1=Clear Channel
2=BONDING mode 1
3=V.120
4=V.34
5=V.110
6=DSU 57.6 ASYNC
7=T-LINK
8=SAP
9=PPP asyn-sync