AMX Modero CV7 - Manual (Page 161)

Programming
149 7" Modero Touch Panels
"^" Button Commands (Cont.)
^BMF
Set any/all button
parameters by
sending
embedded codes
and data.
Syntax:
"'^BMF-,,'"Variables: variable text address char array = 1 - 4000.button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).level range = 1 - 600 (level value is 1 - 65535).data: ’%B’ = Set the border style name. See theBorder Styles table on
page 141.’%B’, = Set the borer style number. See theBorder Styles table on
page 141.’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 146 for more information.’%F’, = Set the font. See theDefault Font Styles and ID
Numbers table on page 141.’%F’ = Set the font. See theDefault Font Styles and ID
Numbers table on page 141.’%MI’ = Set the mask image. Refer to the ^BMI command on page 150 for
more information.’%T’ = Set the text using ASCII characters (empty is clear).’%P’ = Set the picture/bitmap filename (empty is clear).’%I’,’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).’%J’, = As shown the following telephone keypad alignment
chart: ’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’For some of these commands and values, refer to theRGB Values for all 88 Basic
Colors table on page 139. ’%CF’ = Set Fill Color.’%CB’ = Set Border Color.’%CT’ = Set Text Color.’%SW<1 or 0>’ = Show/hide a button.’%SO’ = Set the button sound.’%EN<1 or 0>’ = Enable/disable a button.’%WW<1 or 0>’ = Word wrap On/Off.%GH’ = Set the bargraph upper limit.’%GL’ = Set the bargraph lower limit.’’%GN’ = Set the bargraph slider name/Joystick cursor name.’%GC’ = Set the bargraph slider color/Joystick cursor color.1478963250Zero can be used for an absolute position
Variables:
variable text address char array = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
level range = 1 - 600 (level value is 1 - 65535).
data:
’%B’ = Set the border style name. See theBorder Styles table on
page 141.
’%B’, = Set the borer style number. See theBorder Styles table on
page 141.
’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 146 for more information.
’%F’, = Set the font. See theDefault Font Styles and ID
Numbers table on page 141.
’%F’ = Set the font. See theDefault Font Styles and ID
Numbers table on page 141.
’%MI’ = Set the mask image. Refer to the ^BMI command on page 150 for
more information.
’%T’ = Set the text using ASCII characters (empty is clear).
’%P’ = Set the picture/bitmap filename (empty is clear).
’%I’,’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%J’, = As shown the following telephone keypad alignment
chart:
’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’
’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
For some of these commands and values, refer to theRGB Values for all 88 Basic
Colors table on page 139.
’%CF’ = Set Fill Color.
’%CB’ = Set Border Color.
’%CT’ = Set Text Color.
’%SW<1 or 0>’ = Show/hide a button.
’%SO’ = Set the button sound.
’%EN<1 or 0>’ = Enable/disable a button.
’%WW<1 or 0>’ = Word wrap On/Off.
%GH’ = Set the bargraph upper limit.
’%GL’ = Set the bargraph lower limit.
’’%GN’ = Set the bargraph slider name/Joystick cursor name.
’%GC’ = Set the bargraph slider color/Joystick cursor color.
1
4
7 8 9
6
3 2
5
0
Zero can be used for an absolute position