Scanning problems fax problems – Samsung SCX-5835FN-XAR User Manual
Page 128
Troubleshooting_ 14
Scanning problems
Fax problems
CONDITON
SUGGESTED SOLUTIONS
The scanner does not
work.
•
Make sure that you place the original to be
scanned face down on the scanner glass, or
face up in the document feeder.
•
There may not be enough available memory
to hold the document you want to scan. Try
the Prescan function to see if that works.
Try lowering the scan resolution rate.
•
Check that the machine cable is connected
properly.
•
Make sure that the machine cable is not
defective. Switch the cable with a known
good cable. If necessary, replace the cable.
•
Check that the scanner is configured
correctly. Check scan setting in the
SmarThru Office or the application you want
to use to make certain that the scanner job
is being sent to the correct port (for example,
USB001).
•
In case of use of account feature, make sure
that you have extra scan count remained.
For example, if you try to scan 10-page
document while you have 5 scan count left,
the scan job would be canceled.
The unit scans very
slowly.
•
Check if the machine is printing received
data. If so, scan the document after the
received data has been printed.
•
Graphics are scanned more slowly than text.
•
Communication speed slows in scan mode
because of the large amount of memory
required to analyze and reproduce the
scanned image. Set your computer to the
ECP printer mode through BIOS setting. It
will help to increase the speed. For details
about how to set BIOS, refer to your
computer user’s guide.
Message appears on
your computer
screen:
•
Device can’t be
set to the H/W
mode you want.
•
Port is being used
by another
program
.
•
Port is Disabled.
•
Scanner is busy
receiving or
printing data.
When the current
job is completed.,
try again.
•
Invalid handle.
•
Scanning has
failed.
•
There may be a copying or printing job in
progress. Try your job again when that job is
finished.
•
The selected port is currently being used.
Restart your computer and try again.
•
The machine cable may be improperly
connected or the power may be off.
•
The scanner driver is not installed or the
operating environment is not set up properly.
•
Ensure that the machine is properly
connected and the power is on, then restart
your computer.
•
The USB cable may be improperly
connected or the power may be off.
CONDITION
SUGGESTED SOLUTIONS
The machine is not
working, there is no
display, or the
buttons are not
working.
•
Unplug the power cord and plug it in again.
•
Ensure that there is power being supplied to
the electrical outlet.
No dial tone.
•
Check that the phone line is properly
connected.
•
Check that the phone socket on the wall is
working by plugging in another phone.
The numbers stored
in memory do not
dial correctly.
Make sure that the numbers are stored in
memory correctly. Print a Fax Phone Book list.
(See "Setting up a fax phone book" on page 6.)
The original does
not feed into the
machine.
•
Make sure that the paper is not wrinkled and
you are inserting it in correctly. Check that the
original is the right size, not too thick or thin.
•
Make sure that the document feeder is firmly
closed.
•
The document feeder rubber pad may need to
be replaced. Contact a service
representative.
Faxes are not
received
automatically.
•
The receiving mode should be set to fax.
•
Make sure that there is paper in the tray.
•
Check to see if the display shows any error
message. If it does, clear the problem
The machine does
not send.
•
Make sure that the original is loaded in the
document feeder or on the scanner glass.
•
Check the fax machine you are sending to, to
see if it can receive your fax.
The incoming fax
has blank spaces or
is of poor-quality.
•
The fax machine sending you the fax may be
faulty.
•
A noisy phone line can cause line errors.
•
Check your machine by making a copy.
•
The toner cartridge may be empty. Replace
the toner cartridge. (See "Replacing the toner
Some of the words
on an incoming fax
are stretched.
The fax machine sending the fax had a
temporary document jam.
There are lines on
the originals you
sent.
Check your scan unit for marks and clean it.