Lokar Transmount Emergency Hand Brake - Manual

Building American Quality… With A Lifetime Warranty!
General Installation Notes:
Please read instructions completely before beginning installation.
If you have any questions please call. Before starting installation,
scotch vehicle tires to avoid accidental movement of the vehicle.
Disconnect negative battery cable before beginning installation.
NOTE: This hand brake is designed for use with a Lokar Transmount Shifter and
Lokar Transmount Emergency Brake Cable Kit.
Refer to Fig. 1 for the component names.
Step 1: Install the Lokar Transmount Shifter before beginning installation
of the Emergency Hand Brake.
Step 2: If you are using the Lokar Transmount Emergency Brake Cable
Kit, then remove the clevis pin and clevis from the hand brake
and discard. Make sure to keep the 5/16" flat washer and 1/8"
x 1/2" cotter pin for use during reassembly. Install the clevis
and clevis pin that came with the Lokar Transmount Emergency
Brake Cable Kit into the hand brake. Also discard ONE of the
supplied 3/4" spacers (you will only need one 3/4" spacer with
the Lokar brake cable kit).
If you are NOT using the Lokar Transmount Emergency Brake
Cable Kit, then the supplied clevis may be modified or replaced
as required in order to connect to your existing cables. Make sure
to keep the 5/16" flat washer and 1/8" x 1/2" cotter pin for use
during reassembly. You will use both of the supplied 3/4" spac-
ers to go between the hand brake and the Lokar shifter mount
bracket or your custom bracket.
Step 3: The brake cable bracket from the Transmount Emergency Brake
Cable Kit will be installed at the same time as the hand brake
assembly. Included in the Transmount Emergency Brake Cable
Kit there are three 3/8" spacers and one 1/4" spacer to center
the hand brake in the brake cable bracket. On the front mounting
bolt, install one 3/8" spacer on the right side between the brake
cable bracket and the hand brake, and one 3/4" spacer on the left
between the hand brake and the shifter mount bracket. On the
rear mounting bolt, install one 3/8" spacer on the right between
the brake cable bracket and the hand brake; one 3/8" spacer on
the left between the hand brake and the brake cable bracket; and
one 1/4" spacer between the brake cable bracket and the shifter
mount bracket. Fig. 2
TOLL FREE 1-877-469-7440 • (865) 966-2269 • FAX (865) 671-1999 • [email protected] • www.lokar.com
®
Transmount Emergency Hand Brake Installation Instructions
Transmount Emergency Hand Brake
Installation Instructions
INS0125
Rev. 04/11/13 Page 1 © 2012 Lokar, Inc.
Clevis Pin with 5/16" Flat
Washer and 1/8" x 1/2"
Cotter Pin
3/8"-24 x 2"
Button Head
Bolts
Hand Brake Assembly
Top View
3/4"
Spacers
3/8"-24
Nylock Nuts Clevis
Clevis
Hand
Brake
Shifter
Mount
Bracket
(not included)
Brake Cable
Bracket
(not included)
Step 4: Follow the instructions for the Transmount Emergency Brake Cable
Kit to connect the emergency brake cables. Adjust the hand brake
so that there is no slack, but making sure that the brakes are not
applied when the hand brake is released. Generally, you will want
the cables adjusted so that three clicks of the hand brake will pre-
vent the vehicle from moving (although your braking system may be
different). Your completed installation should look like Fig. 3.
Fig. 1
Fig. 2
3/4” Spacer
1/4” Spacer
Shifter Mount
Bracket (Not
Included) , Bolted
to Transmission
3/8” Spacer
3/8” Spacers
Hand Brake
Assembly
Brake Cable
Bracket
(Not Included)
Front of
Vehicle
Fig. 3