Warren Controls PICV Series - Manual (Page 2)

VALVE BODIES
Body Material: Cast Iron
End Connections: ANSI 125LB FF Flanges, PN16 FF Flanges
Trim Designs: Type 23 - Single Seat Cylinder Balanced, ANSI Class III Leakage
Type 22 and 72 - Double Seat Balanced, ANSI Class III Leakage
Trim Material: Bronze or 300 Series Stainless Steel
EPDM Seal (Type 23 w/Bronze Trim)
Fluoraz Seal (Type 23 w/Stainless Steel Trim)
Fluid: Chilled Water Typical, Water or Water/Glycol from 35 °F- 180°F (2°C - 82°C )
Trim Limits: Stainless Steel: MAX Flowing Differential Pressure, 150 PSIG (10.3 BARG)
Bronze: MAX Flowing Differential Pressure, 100 PSIG (6.9 BARG)
Packing: Long-Life Multi-Stack EPDM Lip Packing - Water / Water-Glycol Service
ELECTRIC ACTUATOR SPECIFICATIONS (VM-1500E AND VM-5000E)
Valve Usage: VM-1500E [Valve sizes 2 1/2, 3 & 4 Inch DN65, DN80 & DN100],
VM-5000E [Valve sizes 5, 6, 8 & 10 Inch DN125, DN150, DN200, DN250]
Control Signal: 4-20 mAdc (Factory Setting), 0-20 mAdc, 0-10 Vdc or 2-10 Vdc
and Floating, Self-Adjusting, Field Selectable (Dip Switch)
Power Consumption: VM-1500E 12VA, VM-5000E 25VA
Timing: VM-1500E [102 sec. / inch, 4.02 sec. / mm], VM-5000E [76 sec. / inch, 2.99 sec./mm]
Feedback Signal: 4-20 mAdc (Factory Setting), 0-10 Vdc or 2-10 Vdc
Failure Mode: Fail-As-Is [Without VMS-25 BCM (Back-up Control Module)]
Fail-Safe [With VMS-25 BCM (Back-up Control Module)]
Manual Override: Yes
Construction: Polycarbonate Motor Housing with Steel Linkage & Yoke.
Case has one 1/2 inch (1.27 cm) NPSM Conduit Adapter
Connections: Coded Screw Terminals
Locations: NEMA Type 3 / IP54
Temperature Limits: Ambient 32°F - 122°F ( 0°C - 50°C )
Mounting: Factory Aligned, Vertical Above Centerline of Control Valve
Consult factory for preconfigured alternate orientations
VMS-25 BCM (BACK-UP CONTROL MODULE) SPECIFICATIONS
Actuator Usage: VM-1500E & VM-5000E
Required for Fail Safe Operation
Failure Direction:
Field Selectable
Power Consumption: 24VAC, 40VA
Construction:
Battery w/Circuit Board & Transformer, in Nema 4 Enclosure
Mounting: Wall Mount
Weight: 4.25 lbs (2 kg)
Body Pressure Temperature Ratings
Iron Body
Temperature 125 FLG & PN16
O F O C PSIG BARG
35 to 180 1.7 to 82.2 150 10.20
CONFIGURATIONS
Control
Valve
Size
Control
Valve
Flange
Control
Valve
Profile
Control
Valve Trim
Size
Control Valve
Trim Material
Control Valve
Motor
DPRV
Size
DPRV
Flange
DPRV
Trim
Material
DPRV Actuator
0 ANSI 125
Flanges
2 PN16
Flanges
22 Type of
Control
Valve
Body
(Sizes P8
& P1)
23 Type of
Control
Valve
Body
(Sizes
P2-P6)
F Control Valve
Trim Size Ful
l
X Control Valve
Trim Size
Extended
1 Control Valve
Trim Size 1SR
2 Control Valve
Trim Size 2SR
S Stainless Steel
B Bronze
E020 VM1500E -
Fail As Is
E021 VM1500E - w/
VMS-25
BCM
E022 VM5000E -
Fail As Is
E023 VM5000E - w/
VMS-25
BCM
TIG1 TR5000-X
-Fail As Is
for all exceot
P6_23XX
Extended Port
TIG2 TR5000-X
-Fail As Is
Extended Port
Only
0 ANSI 125
Flanges
2 PN16 Flanges
Note: Must
match control
valve
DS DPRV Type
72 Portion
w/ SS Trim
DB DPRV Type
72 Portion
w/ Brz
Trim
2L DPRV Actuator Cast
Iron, w/ Low DP Spring
2M DPRV Actuator Cast
Iron, w/ Medium DP
Spring
P2 2.5” DN65
P3 3” DN80
P4 4” DN100
P5 5” DN125
P6 6” DN150
P8 8” DN200
P1 10” DN250
P2 2.5” DN65
P3 3” DN80
P4 4” DN100
P5 5” DN125
P6 6” DN150
P8 8” DN200
P1 10” DN250