Control company – Control Company 5090 OUTLET CONTROLLER User Manual

Page 2

Traceable

To activate the Countdown Timer, press the CD key. To stop the countdown,
press the CD key again amid the display will return to its pre-set countdown
value.

When the Countdown function is operating, the word CD will be flashing on the
display even when the Controller is in other display mode.

Please note that countdown will not start when Random function is activated. All pre-
set programs are also disabled during the countdown period. Activating the Manual
on/off function will cancel the countdown operation.

ACTIVATING THE RANDOM FUNCTIONS
This timer had a built-in random function to automatically turn the timer on and off at
random intervals. The timer will stay on for approximately 10 to 26 minutes and off 26
to 42 minutes. By pressing the RANDOM key, the symbol RND will flash indicating that
it is active. When the random function is active all your preset programs including the
CountDown Program are disabled and remain disabled until the random generator is
turned off by pressing the RANDOM key again.

MANUAL ON/OFF
Without changing the program(s), this Controller can be turned on or off anytime by
using the ON/OFF key.

Press the ON/OFF key to turn the Controller on. Press the ON/OFF key again to turn
the Controller off. The flashing word ON or OFF will indicate that Manual On/Off
function is activated.

ACTIVATING THE DISABLE / MASTER DISABLE FUNCTION
This function allows you to disable and enable any or all of the pre-set ON/OFF
programs and CD Program using the ON/OFF key.

To disable a particular program, display such program or CD Program you wish to
disable using the DOWN or UP (< or >) key, then press the SET key. The display will
be flashing and the word SET will light up. Press the ON/OFF key to disable the
program and the X symbol will appear to indicate that particular program is disabled.

Note: The display is still flashing and if there is no changes made on the pre-set
program time, press the SET key until the display is not flashing. Use this function to
disable as many available preset programs as you choose.

To disable all programs press the SET key while in Clock Display Mode. Then press
the ON/OFF key when the display is flashing to disable all the pre-set programs. The X
symbol appears on the Clock Display Mode indicates that all pre-set programs are
disabled. ~

To cancel this Disable function, just repeat the same procedures to turn off the X
symbol.

AUTO-RETURN/ QUICK JUMP FUNCTION TO CLOCK DISPLAY
If the Controller is left idling for more than 1 minute during programming or displaying
other modes, the display will automatically return to Clock Display Mode and
programming operation will be cancelled. However, if the display is showing
Countdown Timer in progress, auto-return will not activate until countdown has been
finished.

You can also activate the Quick-Jump function by pressing both the DOWN and UP (<
and >) keys together and the display will return to Clock Display Mode immediately.

LCD INDICATOR
The LED indicator shows the status of the Controller. If the LED lights up, it indicates
that the Controller is on and if the LED does not, the Controller is off. Note that the
Controller status can also be seen in the Clock Display mode by the word ON and
OFF. Please note that the LED will only light up when the Controller is plugged into an
electrical outlet.

RESET FUNCTION
To reset all data entries, use a round object such as a ball point pen to push the
RESET key. After reset, all pie-se programs as well as the Cloak Display Mode will be
cleared.

ABNORMAL DISPLAY
When an abnormal display or a blank display appears, use the above Reset
procedures to reset the timer, otherwise the Controller may not be working properly.
Make sure the button cell batteries are in good condition.

TECHNICAL SPECIFICATIONS
Program:

14 programs per day or per week

Minimum switching time: 1 minute
Ratings:

15A 1 2OVAC

Maximum resistive load: 1,800W

WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:

CONTROL COMPANY

4455 Rex Road

Friendswood, Texas 77546 USA

Ph. 281-482-1714 Fax 281-482-9448

E-mail [email protected]

www.control3.com

Control Company is ISO 9001 Quality-

Certified by DNV and ISO 17025 accredited

as a Calibration Laboratory by A2LA.