Control Company 3652 ANEMOMETER/HYGROMETER/THERMOMETER/DEW POINT BAROMETER PEN - Manual

SPECIFICATIONS
Air Flow—
Range:
0.4 to 30.0 m/s (meters per second)
Resolution: 0.1
Range:
1.4 to 108.0 Km/h (kilometers per hour)
Resolution: 0.1
Range: 80 to 5910 FPM (feet per minute)
Resolution: 1
Range:
0.9 to 67.0 mph (miles per hour)
Resolution: 0.1
Range:
0.8 to 58.3 Knot (nautical miles/hour)
Resolution: 0.1
Temperature—
Range:
32.0 to 122.0 °F / 0.0 to 50.0 °C
Resolution: 0.1°
Humidity—
Range:
10.0 to 95.0% RH
Resolution: 0.1%
Dew Point—
Range:
–13.5 to 120.1 °F / –25.3 to 48.9 °C
Resolution: 0.1°
Barometric Pressure—
Range: 10.0 to 1100 hPa (hectopascal)
(1 hectopascal = 1 millibar)
Resolution: 0.1 and 1
Range: 7.5 to 825.0 mmHg (millimeters of mercury)
Resolution: 0.1
Range: 0.29 to 32.48 inHg (inches of mercury)
Resolution: 0.01
Update Rate: 1 second
Battery:
4 each AAA (1.5V)
DISPLAY MODES
The meter may be set to the following display modes:
Humidity and Temperature (Rh/Tmp)
(Humidity reading shown in the upper display, Temperature reading shown in the lower display)
Barometer and Anemometer (Bar/An)
(Barometric pressure reading shown in the upper display, Anemometer reading shown in the lower
display)
Barometer and Humidity (Bar/Rh)
(Barometric pressure reading shown in the upper display, Humidity reading shown in the lower
display)
Barometer and Temperature (Bar/Tmp)
(Barometric pressure reading shown in the upper display, Temperature reading shown in the lower
display)
Anemometer and Temperature (An/Tmp)
(Anemometer reading shown in the upper display, Temperature reading shown in the lower
display)
Humidity and Dew Point (Rh/Dp)
(Humidity reading shown in the upper display, Dew Point temperature shown in the lower display)
To change the display mode, press and hold the REC button until the
reading on the display begins to flash, then release the REC button. With the
readings flashing, each press of the REC button will change the display mode
in sequence
(Rh/Tmp→Bar/An→Bar/Rh→Bar/Tmp→An/Tmp→Rh/DP→Rh/Tmp...).
Once the desired display mode appears, release the HOLD button to select
the display mode (the display will no longer flash).
OPERATION
1. Press the POWER button to turn the meter on.
2. Select the desired display mode (see the
“Display Modes” section).
3. Take the desired measurements.
4. Press the POWER button to turn the meter off.
To preserve battery life, always turn the meter
off when not in use.
If no button is pressed for ten (10) minutes, the meter will turn off
automatically to preserve battery life (see the “Automatic Shutoff” section).
SELECTING °F OR °C
(Temperature/Dew Point)
1. Place the meter into one of the following display
modes that displays a temperature reading:
Rh/Tmp, Bar/Tmp, An/Tmp or Rh/Dp (see the
“Display Modes” section).
2. Press and hold the HOLD button for
approximately five (5) seconds, the unit of
measure will flash on the display.
3. Release the HOLD button and press the REC
button, the temperature reading will switch to the
opposite unit of measure. If the meter had been
displaying °F, it will now display °C, and vice-
versa. Each press of the REC button will switch
the display to the opposite unit of measure.
4. With the desired unit of measure appearing,
press the HOLD button.
The unit of measure selected will be the default unit of measure for both
temperature and dew point until changed.
SELECTING ANEMOMETER UNIT OF MEASURE
1. Place the meter into the Anemometer and
Temperature (An/Tmp) display mode (see the
“Display Modes” section).
TRACEABLE® ANEMOMETER/HYGROMETER/
THERMOMETER/DEW POINT BAROMETER PEN INSTRUCTIONS