Diamond Products UDM User Manual
Diamond Products Power Tools
Table of contents
Document Outline
- 4645159
- Alternator Assembly
- blankmaintanence
- Cover
- Dash Panel Assembly
- Hydraulic System
- Inner Dash & Fuses
- Mast Assembly
- Operating Manual
- Pg1
- Pg2
- Pg4
- Pg5
- Pg6
- Pg7
- Pg8
- Pg9
- Pg10
- Pg11
- Pg12
- Pg13
- Pg14
- Pg15
- Pg16
- Pg17
- Pg18
- Pg19
- Pg20
- Pg21
- Pg22
- Pg23
- warranty page.pdf
- UDM Assembly Overview.PDF
- UDM Drive Train.PDF
- 4645159.PDF
- Sheet1
- Drawing View1
- Drawing View2
- Sheet1
- Alternator Assembly.PDF
- Sheet1
- Drawing View1
- Drawing View3
- Sheet1
- Vacuum Pump.PDF
- Outlet Box1.PDF
- Dash Panel Assembly.PDF
- Sheet1
- Drawing View3
- Sheet1
- Rear Stabalizer.PDF
- Vacuum Base Assembly.PDF
- Mast Assembly.PDF
- Sheet1
- Drawing View1
- Sheet1
- Hydraulic System.PDF
- Sheet1
- Drawing View1
- Drawing View2
- Detail View A (1 : 16)
- Sheet1
- Inner Dash & Fuses.PDF
- Sheet1
- Drawing View10
- Section View A-A
- Sheet1
- Outlet Box1
- Sheet1
- Drawing View1
- Drawing View2
- Sheet1
- Outlet Box2
- Sheet2
- Pg1
- Safety Precautions
- Safety Alerts
- Proposition 65
- Spark Arrester Requirement
- Respiratory Hazards
- Safety Precautions
- Pg10
- Engine
- /
- Tasks Prior to Starting the Engine
- Starting the Engine
- Stopping the Engine
- Drive Lever
- The drive lever moves the machine at variable speeds based on its position. The maximum driving speed with the engine running is ~3.25 mph. Use the handlebars to lift the rear tires off the ground and pivot, push, or pull the machine manually.
- Pg11
- Pg12
- Pg13
- Inspecting the Core Bit
- Core Bit Speeds
- Installing a Core Bit
- Pg14
- Helpful Hints Prior to Drilling
- Tasks Prior to Drilling
- Pg15
- Drilling a Hole
- Continuing a Partial-Hole
- Stuck Cores
- Removing a Stuck Core
- Stuck Bits
- Pg16
- Removing a Stuck Bit
- Pg17
- Pg18
- Battery
- Battery Type
- Servicing the Battery
- Electrical System
- Fuse Panel
- Circuit Breakers
- Battery
- Pg19
- Hydraulic System/
- Changing the Hydraulic Oil
- Changing the Hydraulic Oil Filter
- Belt System
- Tensioning the Engine Belt
- Hydraulic System/
- Pg2
- General Safety
- Battery and Electrical Safety
- Pg20
- Replacing the Engine Belt
- Engine Throttle Screw
- Pg21
- Pg22
- Appendix C
- Belt Tension Setting
- Appendix D
- Additional Resources
- Appendix C
- Pg23
- Appendix E
- Troubleshooting
- Appendix E
- Pg3
- Pg4
- Hydraulic Safety
- Belt Safety
- Transporting Safety
- Lifting Safety
- Pg5
- Introducing the UDM
- Components
- Introducing the UDM
- Pg6
- Controls
- Pg7
- Pg8
- Pg9
- Rear Stabalizer
- Sheet1
- Drawing View1
- Sheet1
- Table of Contents
- UDM Assembly
- Sheet1
- Drawing View1
- Drawing View2
- Sheet1
- UDM Assembly Overview
- Sheet1
- Drawing View1
- Drawing View2
- Sheet1
- UDM Drive Train
- Sheet1
- Drawing View1
- Drawing View3
- Sheet1
- UDM Water & Vacuum Systems
- ULITIMATE DRILLING MACHINE DECAL KIT
- ULTIMATE DRILLING MACHINE DRILLING MAST ASSEMBLY
- ULTIMATE DRILLING MACHINE DRIVE TRAIN ASSEMBLY
- ULTIMATE DRILLING MACHINE ELECTRICAL OUTLET BOX
- ULTIMATE DRILLING MACHINE HYDRAULIC SYSTEM PARTS LIST
- ULTIMATE DRILLING MACHINE Operating Summary
- ULTIMATE DRILLING MACHINE WATER
- Vacuum Base Assembly
- Sheet1
- Drawing View1
- Sheet1
- Vacuum Pump
- Sheet1
- Drawing View1
- Detail View A (1 : 4)
- Sheet1
- warranty page
- WARRANTY
- Diamond Products warrants all equipment manufactured by it against defects
- THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
- OR IMPLIED, AND ALL SUCH OTHER WARRANTIES ARE HEREBY
- DISCLAIMED.
- Diamond Products warrants all equipment manufactured by it against defects
- WARRANTY
- 4645215.PDF