Chapin 31410 - Manual

6-4626
Shut-off Handle
Mango de cierre
Poignée du robinet
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or le ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
Parts, Piezas, Pièces
6-6136
Hose
Manguera
Tuyau
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
Printed in USA
1. Hose to Tank
2. Nozzle
Attach nozzle to shut-off handle or extension wand.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank
outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these
conditions are found, replace hose before using. Replace with original manufacturer’s
parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect
interior and exterior of tank for signs of deterioration of body and bottom. Any sign
of deterioration indicates possible tank weakening and could result in explosive
bursting under pressure. If any of these signs are found, discard tank immediately and
replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 10-20 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions),
empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on
chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to
accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump
in tank and tighten securely.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,
Pressurizing and Spraying Instructions, except pump unit only 10-15 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and
empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.
6-5943
Nozzle
Tobera
Buse
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡
Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
011269 (A) R0000
6-3337
Strap , Correa, Sangle
( 31020, 31030, 36140, 30220)
6. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until
air begins to escape. Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
6-7756 Extension wand, Vara de extensión, Rallonge
(31010, 31020, 31030, 36140)
6-7749 Extension wand, Vara de extensión, Rallonge
(30220)
Make sure hose is pushed all the way to
the tank. Make sure hose clamp is tight
and below the hose barb. Turn clockwise
with a screwdriver to tighten.
Hose Barb
8. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle
and move grey locking mechanism away from you.
To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are
provided with this feature).
8A
Locking
mechanism
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
1A
2B 2A
5. Pressurizing and Spraying
Pump until you feel
resistance.
Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn
counterclockwise to
release.
Push handle, down,
turn 1/4 turn clockwise
to lock. Begin spray-
ing.
Re-pump sprayer as
required to maintain
spray force.
Adjust spray pattern
by turning nozzle cap.
Do not turn cap more
than 2 turns or cap may
come off allowing spray
material to spray back
on you.
5C 5B 5A
5D
Pull handle
straight up.
Insert notches from un-
derside of handle into
plunger grooves and
turn counterclockwise.
Remove plunger and diaphragm.
Clean plunger, diaphragm and body. Flip
diaphragm and replace.
Tighten plunger clockwise until flush
to top of shut-off body. Do not over-
tighten or unit may not spray. Slide
forks under plunger, push handle
down until it snaps into place.
9. Troubleshooting
- Tank pressurizes but does not spray.
9A 9B Handle 9C
Plunger
Body
Diaphragm
9D
Plunger flush
with body
WARNING:
Release pressure in tank before troubleshooting.
Clean Nozzle Assembly (Fig. 9E) - Remove nozzle cap. Clean and re-assemble.
Clean shut-off (Fig. 9A- 9D)
9E
Nozzle Cap