Chapin 21210 User Manual

Warning, Pre-use check 5. filling, Pressurizing and spraying

WARNING!

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of

these conditions are found, replace hose before using. Replace with original manufacturer’s

parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior

and exterior of tank for signs of deterioration of body and bottom. Any sign of

deterioration indicates possible tank weakening and could result in explosive bursting

under pressure. If any of these signs are found, discard tank immediately and replace.

Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.

5) Do: Pump plunger 10-20 strokes and inspect for leaks.

6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty

tank, and proceed with Filling, Pressurizing and Spraying Instructions.

4. Pre-Use Check

5. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to

accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in

tank and tighten securely.

6. Pressurizing and Spraying

Do:

Turn handle clock-

wise to tighten. Push

handle down, turn 1/4

turn counterclockwise to

release.

Do:

Pump until

you feel resistance.

Do:

Push handle,

down, turn 1/4 turn

clockwise to lock. Be-

gin spraying. Re-pump

sprayer as required to

maintain spray force.

8. To Release Pressure

1) Your sprayer is equipped with a pressure relief/release valve.

To release pressure lift and hold the cap until air is completely

exhausted, OR, turn the valve slowly counterclockwise until you

hear air escaping and wait air is completely exhausted.

2) Do: Stay away from the sprayer until all air has escaped.

9. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,

Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and

empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod

through opening in cover.

010522-1 (A) R0610

WARNING:

Handling the brass parts of this product will expose you to lead, a chemical known to the State of

California to cause birth defects and other reproductive harm. Wash hands after handling.

2. Nozzle

Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye

or other injury.

For safe use of this product you must read and follow all instructions. Do not leave a pressur-

ized sprayer in the hot sun. Heat can cause pressure build-up. Do not store or le

ave solution in tank after use.

Always wear goggles, gloves, long sleeve shirt, long pants and full foot protection when spraying. Never use

any tool to remove pump if there is pressure in sprayer. Never stand with face or body over

top of tank when

pumping or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring

you. Never pressurize sprayer by any means other than the original pump. Do not attempt to modify or repair

this product except with original manufacturer’s parts. Never spray flammable materials or heat, pressure, or

gas producing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer

as some chemicals may be hazardous when used with this sprayer.

Sk-1113-1

For constant spraying, push down on shut-off

handle and move locking mechanism away

from you. To release, squeeze handle and

move the locking mechanism back towards

you.

7. Fatigue-Free Spraying

P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4627

Congratulations!

You have just purchased a quality Chapin product.

Questions?

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

¡Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com

¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com

Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse

www.chapinmfg.com

Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

1. Hose to Tank

Discharge/ Assembly

• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).

• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).

• Proper placement of white outlet tube (Fig. 1C).

• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab

with notches on the tank adapter.

• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).

Discharge

Assembly

Outlet

Tube

Retaining Nut -

Securely tightened.

Gap

Tank

Adapter

Outlet Tube

Adapter

Tab/

Notch

Outlet Tube

Adapter

Outlet

Tube

6-6136

Hose

Manguera

Tuyau

6-3337

Straps

Tirantes

Sangles

Parts, Piezas, Pièces

6-5383

Relief Valve Kit

Equipo de la válvula de descarga

Kit de soupape de sécurité

6-6000

Nozzle

Tobera

Buse

6-1866

Shut-off Handle

Mango de cierre

Poignée du robinet

6-7711

Extension wand

Vara de extensión

Lance de rallonge

Attach nozzle to shut-off handle or extension wand.

3. Filter

The filter helps prevent clogging while spraying. It

is located on the end of the white tube inside your

sprayer tank.To clean filter, remove the hose from the

tank and lift out the outlet tube. Make sure the filter

is positioned at the bottom of the tank as pictured.

Filter

This manual is related to the following products:

21220 21230