Chapin 20075 User Manual

Warning, Pressurizing and spraying, Parts, piezas, pièces

Sk-1157-1

1. Assembly

Attach extension wand to shut-off handle.

2. Pre-Use Check

3. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten

securely.

6. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and

Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are

thoroughly rinsed with water after each use.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.

011620 (A) R0000

• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter

and outlet tube adapter. Firmly tighten the retaining nut to the tank adapter (Fig. 1C).

To prevent hose from blowing off, hose must cover both barbs on the outlet tube adapter and

touch flange (Fig. 1B) before hose nut is securely tightened (Fig. 1C).

4. Pressurizing and Spraying

Do:

Turn handle

clockwise to tighten.

Push handle down,

turn 1/4 turn

counterclockwise to

release.

Do:

Pump until

you feel resistance.

Do:

Push handle,

down, turn 1/4 turn

clockwise to lock. Be-

gin spraying. Re-pump

sprayer as required to

maintain spray force.

Do:

Turn end of

nozzle to adjust spray

pattern.

Retaining Nut -

Securely tightened.

Tool

Holder

Outlet

Tube

Discharge

Assembly

No Gap

Tank

Adapter

Outlet

Tube

Adapter

Filter

7. Troubleshooting

Tank pressurizes but does not spray.

WARNING: Release pressure in tank before troubleshooting.

Pull handle

straight up.

Insert notches

from underside

of handle into

plunger grooves

and turn counter-

clockwise.

Remove plunger and

diaphragm.

Clean plunger, diaphragm

and body. Flip diaphragm

and replace.

Tighten plunger clock-

wise until flush to top

of shut-off body. Do not

over-tighten or unit may

not spray. Slide forks under

plunger, push handle down

until it snaps into place.

Handle

Plunger

Body

Diaphragm

Plunger flush

with body

A) Clean shut-off (Fig. 7A- 7D)

1 piece style

B) Clean Nozzle Assembly (Fig. 6E) -Remove nozzle cap. Clean and re-assemble.

Nozzle Cap

C) Filter

The filter helps prevent clogging while spraying. It is located

on the end of the outlet tube inside your sprayer tank.To clean

filter, remove the discharge assembly from the tank (Fig.1A).

Make sure the filter is positioned at the bottom of the tank as

pictured (Fig. 7F).

Filter

7 F

WARNING

5. To Release Pressure

Do: With pump facing away, turn locked handle counterclockwise until air begins to escape. Stop turning

handle when you hear air escaping. Do: Point pump away until all air escaped.

#20075

1-4571

Filter

Filtro

Fitre

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury.

For safe use of this product you must read and follow all instructions. Do not leave a pres-

surized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not store or

leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot protec-

tion when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with face or

body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or solution

from striking and injuring you. Never pressurize sprayer by any means other than original pump. Do not at-

tempt to modify this sprayer. Replace parts only with manufacturer’s original parts. This sprayer is designed

for use with bleach solutions only. Never use or mix bleach or solutions containing bleach with other

household chemicals such as toilet bowl cleaners, rust removers, acids or ammonia containing products.

Never spray flammable, acidic, caustic or other corrosive solutions or heat, pressure, or gas producing

chemicals. Always read and follow chemical manufacturer’s instructions before use with this sprayer as

some chemicals may be hazardous when used with this sprayer.

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,

replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of

tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank

weakening and could result in explosive bursting under pressure. If any of these signs are found, discard

tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20

strokes and inspect for leaks).

5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed

with Filling, Pressurizing and Spraying Instructions.

7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of

these conditions are found, replace affected part with original manufacturer’s part before using.

Congratulations!

You have just purchased a quality Chapin product.

Questions?

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com

¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse

suivante: www.chapinmfg.com

Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

Note: Your particular sprayer may not include all parts pictured above.

Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)

6-1925

P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com

Parts, Piezas, Pièces

6-2001

Hose Kit: 2 nuts, 2 barbs and hose

Juego de manguera: 2 tuercas ,2

lengüetas y manguera.

Nécessaire de tuyau: Deux écrous,

deux ardillons et tuyau

6-2000

Shut-off Handle

Mango de cierre

Poignée du robinet

6-6003

Nozzle

Boquilla

Buse

6-7749

Extension wand (brass)

Vara de extensión, Lance de rallonge