Chapin 22049XP User Manual

Warning, Pre-use check 4. filling, Care, storage and maintenance

WARNING!

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.

9. Care, Storage and Maintenance

010963-1 (A) R0412

301219

Shut-off

P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com

WARNING:

Handling the brass parts of this product will expose you to lead, a chemical known

to the State of California to cause birth defects and other reproductive harm. Wash hands after

handling.

2. Nozzle

Attach nozzle to shut-off handle or extension wand.

1. Hose to Tank

Discharge/ Assembly

• Make sure white outlet tube is attached to outlet tube adapter (Fig. 1A).

• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1B).

• Proper placement of white outlet tube (Fig. 1C).

• Firmly insert the outlet tube adapter into the tank adapter (Fig. 1D) Lining up tab

with notches on the tank adapter.

• Firmly tighten the retaining nut to the tank adapter (Fig. 1E).

Discharge

Assembly

Outlet

Tube

Retaining Nut -

Securely tightened.

Gap

Tank

Adapter

Outlet Tube

Adapter

Tab/

Notch

Outlet Tube

Adapter

Outlet

Tube

7. To Release Pressure

1) Your sprayer is equipped with a pressure relief/release
valve (Fig. 7A). To release pressure lift and hold the cap
until air is completely exhausted, OR, turn the valve slowly
counterclockwise until you hear air escaping and wait air is
completely exhausted (Fig. 7B).
2) Do: Stay away from the sprayer until all air has escaped.

Parts, Piezas, Pièces

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)

6-4603

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

For constant spraying, push down on shut-off handle and
move locking mechanism away from you. To release, squeeze
handle and move the locking mechanism back towards you.

6. Fatigue-Free Spraying

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior
of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any
of these conditions are found, replace affected part with original manufacturer’s part before using.

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing
and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and nozzle are
thoroughly rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.

Sk-1154-1

WARNING: Improper use or failure to follow instructions can result in explosive failure caus-

ing serious eye or other injury.

For safe use of this product you must read and follow all instruc-

tions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting

in possible explosion. Do not store or leave solution in tank after use. Always wear goggles, gloves,

long sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove

pump if there is pressure in sprayer. Never stand with face or body over top of tank when pumping

or loosening pump to prevent ejecting pump assembly and/or solution from striking and injuring

you. Never pressurize sprayer by any means other than the original pump. Do not attempt to modify

this sprayer. Replace parts only with manufacturer’s original parts. Never spray flammable, caustic,

acidic, chlorine, bleach or other corrosive solutions or heat, pressure, or gas producing chemi-

cals. Always read and follow chemical manufacturer’s instructions before use with this sprayer

as some chemicals may be hazardous when used with this sprayer.

5. Pressurizing and Spraying

Do:

Turn handle clockwise

to tighten. Push handle

down, turn 1/4 turn coun-

terclockwise to release.

Do:

Pump until you

feel resistance.

Do:

Push handle, down, turn

1/4 turn clockwise to lock.

Begin spraying. Re-pump

sprayer as required to maintain

spray force.

8. Wand Dock Clip

Choose the holder that fits your wand.

6-4607

Pressure Relief Valve

Válvula de descarga de presión

Soupape de décompression

6-7705

Extension wand

Vara de extensión

Lance de rallonge

6-5797

Nozzle

Tobera

Buse

6-5943

Nozzle

Tobera

Buse

301630-3

Pump Assembly

Asamblea de la bomba

Assemblée de pompe