Chapin 19149 User Manual

Warning, Pre-use check 4. filling, Care, storage and maintenance

Hazard: Improper use or failure to follow instructions can result in explosive failure causing

serious eye or other injury.

For safe use of this product you must read and follow all instructions.

Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store

or le

ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full

foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.

Never stand with face or body over

top of tank when pumping or loosening pump to prevent eject-

ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any

means other than the original pump. Do not attempt to modify or repair this product except with

original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-

ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer

as some chemicals may be hazardous when used with this sprayer.

WARNING!

Sk-1113-1

Repair Parts Kit Gaskets and Seals (not included),

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4629

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are

found, replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and

exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration

indicates possible tank weakening and could result in explosive bursting under pressure. If

any of these signs are found, discard tank immediately and replace. Do not attempt to patch

leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.

5) Do: Pump plunger 10-20 strokes and inspect for leaks.

6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,

and proceed with Filling, Pressurizing and Spraying Instructions.

3. Pre-Use Check

4. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate

pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank

and tighten securely.

8. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,

Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.

WARNING:

Handling the brass parts of this product will expose you to lead, a chemical known

to the State of California to cause birth defects and other reproductive harm. Wash hands after

handling.

011533-1 (A) R0000

1. Hose to Tank

2. Nozzle

Parts, Piezas, Pièces

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Attach the hose by screwing the swivel nut

clockwise and tightening to 37 in. lbs. Refer

to Pre-use check before using.

6-5373

Holster

Funda

Étui

6-8136

Valve Kit

Kit de la válvula

Ensemble de soupape

6-8135

Dripless Shut-off

Cierre antigoteo

Arrêt anti-goutte

Attach nozzle to shut-off handle or extension wand.

TO LOCK HANDLE:

Push handle down to

depress coil spring and turn handle 1/4 turn

clockwise, then allow handle to raise into lock

position.

Lock

Position

TO RELEASE HANDLE: Push down to

depress coil spring and turn handle counter-

clockwise 1/4 turn, then lift handle.

Pump until you feel

resistance.

TO LOCK PUMP: Place pump prongs down into

slots in funnel, turn clamp clockwise to furthest

position under bottom slot, then turn handle

clockwise until tightly locked and sealed in place.

TO UNLOCK PUMP: Turn handle counterclockwise

until 3-prong clamp is loose. Then rotate clamp counter-

clockwise to stop and lift out.

5. Pressurizing and Spraying

For safety lock-off feature (no-spraying), push trigger

forward and rotate locking mechanism into lock-off

position as shown in fig. 6A.

6. Lock Off

7. To Release Pressure

1 Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.

Stop turning handle when you hear air escaping.

2) Do: Stay away from the sprayer until all air has escaped.

6-6091

Hose Brown

Manguera Castaño

Tuyau Brun

6-5943

Nozzle 1.0 GPM

Tobera

Buse

6-5797

Nozzle .5GPM

Tobera

Buse

Congratulations!

You have just purchased a quality Chapin product.

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:

www.chapinmfg.com
Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

6-6092

Hose Black

Manguera para trabajos pesados Negro

Tuyau pour service intense Noir

Valve Seat

Nozzle Adapter

Nozzle

To attach nozzle to shut-off, unthread nozzle adapter and re-

move valve seat from extension (2B). Unthread brass extension

nut and metal rod (2D). Assemble valve seat to shut-off then

assemble nozzle adapter as shown in figure (2A).

Note orientation of valve seat. It will leak if assembled wrong .

Lock

Trigger

Metal Rod

Brass Extension

Brass Extension Nut

Metal Rod

This manual is related to the following products:

19249