Burkert Type 8635 - Manual

Device-related notes
Control valve with
SIDE Control
Fluid Control Systems Quickstart Installation and Operation
GENERAL NOTES
Intended use
Please observe the notes in these operating instructions
together with the conditions of use and permitted data
that are specified in the data sheet Type 8635, in order that the
device will function perfectly and remain operable for a long time.
On non-observance of these notes and unauthori-zed interference
with the device, we will refuse all liability and the warranty on
device and accessories will become void! The device serves
exclusively as a positioner and process control system.
Any other use or use exceeding the specific scope is considered
to be
non-intended use. Bürkert will not be liable for any
damage resulting therefrom. The risk will be borne by the user.
GENERAL NOTES TECHNI
Technic
• Analog
• Inductiv
• Binary
• Commu
• Softwa
This device contains electronic components that are sensitive
to electrostatic discharge (ESD). Contact to electrostatically
charged persons or objects will endanger these components.
In the worst case, they will be immediately destroyed or will fail
after commissioning.
Observe the requirements of EN 100015-1 (IEC 61340-5-1) in order
to minimize the possibility of, or avoid, damage from instantaneous
electrostatic discharge. Also take care not to touch components that
are under supply voltage.
ATTENTION
EXERCISE CAUTION ON HANDLING!
ELECTROSTATICALLY SENSITIVE
COMPONENTS / MODULES
• For installation and operation in potentially explosive zones,
observe the relevant national regulations (in EN 60079-14 /
IEC 60079-14).
• On electrical connection of inherently safe circuits, observe the
information on the relevant declaration of conformity
(see O
perating Instructions on CD).
• Take suitable precautions to prevent electrostatic charging
of plastic parts of the housing (see EN 100015-1 / IEC 61340-5-1).
• No components shall be connected to the inputs and outputs of the
boards whose electrical data lie outside the limits stated on the
data sheet for the positioner.
• Only inherently safe devices (according to EN 50020 /
IEC 60079-11) shall be connected to the serial interface in
potentially explosive zones.
• The plastic covering shall be removed only by the manufacturer.
• Interventions in the device with the housing open shall not be carried
out in very humid or aggressive atmospheres.
Limit the duration of opening of the housing to that which is
absolutely necessary.
• The design type inspection certificate is to be found in the
Operating Instructions on the CD. We reserve
These instructions explain with the aid of an example the com-
missioning of a single-acting control valve. A detailed descrip-
tion of the device can be found in the operating instructions for
the SIDE
Control Type 8635, as well as in the operating instruc-
tions for the process valves on the accompanying CD.
Possibl
(EEx ia
• Keep to standard engineering rules in planning the
use of and operating the device!
• Installation and intervention for maintenance work
are only allowed by qualified personnel using
suitable tools!
• Observe the current regulations on accident
prevention and safety for electrical devices during
operation and maintenance of the device!
• Before interfering with the system, always switch off
the voltage!
• Note that in systems under pressure, piping and
valves may not be loosened!
• Take suitable precautions to prevent inadvertent
operation or damage by unauthorized action!
• After interruption of the electrical or pneumatic
supply, make sure the process is restarted in a well-
defined, controlled manner!
Safety notes
GB
n i t a r e p O
t n e i b m A
n o i t c e t o r P
a c i r t c e l E
s t n e r r u C
v n e d r u B
e r n e d r u B
n o i t c e t o r P
t a m u e n P
m l o r t n o C
o c t s u D -
c r e t a W -
t n o c li O -
t a r e p m e T
s s e r p m o c
e r u s s e r P