Burkert Type 6013 - Manual

Bedienungsanleitung
Manuel d‘utilisation
Operating Instructions
Type 6013
Magnetventil
2/2-Way Solenoid Valve
2/2-Wege Magnetventil
Électrovanne à 2/2 voies
Address / Adresse
Germany / Deutschland / Allemagne
Bürkert Fluid Control Systems
Sales Center
Christian-Bürkert-Str. 13-17
D-74653 Ingelfingen
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
E-mail: [email protected]
International
www.burkert.com → Bürkert → Company → Locations
Manuals and data sheets on the Internet:
www.burkert.com
Bedienungsanleitungen und Datenblätter im Internet:
www.buerkert.de
Manuel d'utilisation et fiches techniques sur Internet :
www.buerkert.fr
© 2013 Bürkert Werke GmbH
Operating Instructions 1306/21_EU-ml_00803465 / Original
DE
1. Operating instructiOns
The operating instructions contain important information.
• Read the instructions carefully and follow the safety instructions in
particular, and also observe the operating conditions.
• Instructions must be available to each user.
• The liability and warranty for Type 6013 are void if the operating
instructions are not followed.
2. symbOls
→
designates a procedure which you must carry out.
Warning of serious or fatal injuries:
DAnGer!
In case of imminent danger.
WArnInG!
In case of potential danger.
Warning of minor or moderately severe injuries:
CAutIon!
Warns of damage to property:
note!
3. intended use
Incorrect use of the solenoid valve Type 6013 can be dangerous
to people, nearby equipment and the environment.
• The device is designed for blocking, dosing, filling and venting neutral
gaseous and liquid media.
• Use according to the permitted data, operating conditions and con-
ditions of use specified in the contract documents and operating
instructions.
• The device may be used only in conjunction with third-party devices
and components recommended and authorised by Bürkert.
• Correct transportation, correct storage and installation and careful
use and maintenance are essential for reliable and problem-free
operation.
• Use the device only as intended.
3.1. restrictions
If exporting the system/device, observe any existing restrictions.
3.2. approvals
The approval mark indicated on the Bürkert labels refers to the
Bürkert products.
english
4. basic safety instructiOns
These safety instructions do not make allowance for any contin-
gencies and events which may arise during installation, operation and
maintenance.
Danger – high pressure!
• Before loosening the lines and valves, turn off the pressure and
vent the lines.
Risk of electric shock!
• Before reaching into the system,
switch off the power supply and
secure to prevent reactivation!
• Observe applicable accident prevention and safety regulations for
electrical equipment!
Risk of burns/risk of fire!
During continuous operation the surface of the device may become hot.
• Keep the device away from highly flammable substances and media
and do not touch the device with bare hands.
• Do not obstruct the heat release required for operation.
Destruction of the coil by overheating!
• Connect the coil electrically only when the housing has been installed.
• In the case of AC voltage pay attention to movable core.
e
1
03 5791
Devices which must bear the type approval mark were approved at
the Kraftfahrtbundesamt under the type approval number:
e1*72/245*2006/96*5791*00
and are put into circulation with the indicated type approval mark. You
can obtain an extract of the type approval from the address below.
Bürkert Werke GmbH
Zulassungsbeauftragter,
Christian-Bürkert-Str. 13-17,
D-74653 Ingelfingen
3.3. ex approval
• The Ex approval is only valid if you use the modules and components
authorized by Bürkert as described in these operating instructions.
• You may use the electronic modules only in combination with the
pneumatic valve types released by Bürkert, otherwise the Ex approval
will be void.
• If you make unauthorized changes to the system, the modules or
components, the Ex approval will also be void.
english