Atec Kikusui-PLZ-4W Series - Manual (Page 9)

9 P L Z - 4 W S E R I E S
[rating]
*1 The minimum operating voltage
(including the voltage drop due
t o t h e w i r e i n d u c t a n c e
component) in switching mode
increases by 0.15 V per 1 A/
μs
at slew rate settings greater than
5 A/
μs.
*2 The minimum operating voltage
(including the voltage drop due
t o t h e w i r e i n d u c t a n c e
component) in switching mode
increases by 0.3 V per 1 A/
μs at
slew rate settings greater than 5
A/
μs.
*3 Minimum voltage at which the
current star ts flowing to the
PLZ-4W. (The PLZ-4W detects
no signal at an input voltage less
than or equal to approximately
0.3 V and an input current less
than or equal to approximately 1
% of the range rating. Therefore,
if the input voltage is gradually
increased from 0 V, no current
will flow until 0.3 V is exceeded.
Once a current greater than or
equal to 1 % of the range rating
starts flowing, the current can
flow at voltages less than equal
to 0.3 V.)
[CC mode]
*1 Full scale of H range
*2 Vin: Input terminal voltage of
Electronic Load
*3 When the input voltage is varied
from 1.5 V to 150 V at a current
of rated power/150 V.
*4 M e a s u r e m e n t f r e q u e n c y
bandwidth: 10 Hz to 1 MHz
*5 M e a s u r e m e n t f r e q u e n c y
bandwidth: 10 Hz to 20 MHz
*6 At measurement current of 100 A
[CR mode]
*1 Conductance [S] = Input current [A]/
input voltage [V] = 1/resistance [ Ω]
*2 Conver ted value at the input
current. At the sensing point.
*3 set = Vin/Rset
*4 Full scale of H range
[CV mode]
*1 With respect to a change in the
current of 10 % to 100 % of the
rating at an input voltage of 1.5 V
(during remote sensing).
[CP mode]
*1 Full scale of H range
Rating
Model PLZ164W PLZ334W PLZ1004W PLZ164WA PLZ664WA
Operating voltage (DC) 1.5 V – 150 V * 1 0 V – 150 V * 2
Current 33 A 66 A 200 A 33 A 132 A
Power 165 W 330 W 1000 W 165 W 660 W
Minimum start voltage * 3 0.3 V or greater
CC mode
Model PLZ164W PLZ334W PLZ1004W PLZ164WA PLZ664WA
Operating
range Range H 0 A – 33 A 0 A – 66 A 0 A – 200 A 0 A – 33 A 0 A – 132 A
M 0 A – 3.3 A 0 A – 6.6 A 0 A – 20 A 0 A – 3.3 A 0 A – 13.2 A
L 0 A – 330 mA 0 A – 660 mA 0 A – 2 A 0 A – 330 mA 0 A – 1.32 A
Setting range Range H 0 A – 34.65 A 0 A – 69.3 A 0 A – 210 A 0 A – 34.65 A 0 A – 138.6 A
M 0 A – 3.465 A 0 A – 6.93 A 0 A – 21 A 0 A – 3.465 A 0 A – 13.86 A
L 0 A – 346.5 mA 0 A – 693 mA 0 A – 2.1 A 0 A – 346.5 mA 0 A – 1.386 A
Resolution Range H 1 mA 2 mA 10 mA 1 mA 10 mA
M 0.1 mA 0.2 mA 1 mA 0.1 mA 1 mA
L 0.01 mA 0.02 mA 0.1 mA 0.01 mA 0.1 mA
Accuracy of
setting Range H, M ±(0.2 % of set + 0.1 % of f.s * 1 ) + Vin * 2 /500 k Ω
L ±(0.2 % of set + 0.1 % of f.s)
Input voltage
variation
* 3
Range H 2 mA 4 mA 10 mA 2 mA 8 mA
M 2 mA 4 mA 10 mA 2 mA 8 mA
L 0.1 mA 0.2 mA 0.6 mA 0.1 mA 0.4 mA
Ripple rms * 4 3 mA 5 mA 20 mA * 6 7.5 mA 30 mA * 6
p-p * 5 30 mA 50 mA 100 mA * 6 50 mA 200 mA * 6
CR mode
Model PLZ164W PLZ334W PLZ1004W PLZ164WA PLZ664WA
Operating
range
* 1
Range H 22 S – 400 μS
(45.455 m Ω – 2.5 kΩ)
44 S – 800 μS
(22.727 m Ω – 1.25 kΩ)
133.332 S – 2.4 mS
(7.5 m Ω – 416.666 Ω)
22 S – 400 μS
(45.455 m Ω – 2.5 kΩ)
88 S – 1.6 mS
(11.363 m Ω – 625 Ω)
M 2.2 S – 40 μS
(454.55 m Ω – 25 kΩ)
4.4 S – 80 μS
(227.27 m Ω – 12.5 kΩ)
13.3332 S – 2420 μS
(75 m Ω – 4.1666 kΩ)
2.2 S – 40 μS
(454.55 m Ω – 25 kΩ)
8.8 S – 160 μS
(113.63 m Ω – 6.25 kΩ)
L 0.22 S – 4 μS
(4.545 5 Ω – 250 kΩ)
0.44 S – 8 μS
(2.272 7 Ω – 125 kΩ)
1.33332 S – 24 μS
(750 m Ω – 41.666 kΩ)
0.22 S – 4 μS
(4.545 5 Ω – 250 kΩ)
0.88 S – 16 μS
(1.136 3 m Ω – 62.5
k Ω)
Setting range Range H 23.1 S – 0 S
(43.290 m Ω – OPEN)
46.1 S – 0 S
(21.692 m Ω – OPEN)
139.9968 S – 0 S
(7.1430 m Ω – OPEN)
23.1 S – 0 S
(43.290 m Ω – OPEN)
92.4 S – 0 S
(10.822 m Ω – OPEN)
M 2.31 S – 0 S
(432.9 m Ω – OPEN)
4.61 S – 0 S
(216.92 m Ω – OPEN)
13.99968 S – 0 S
(71.430 m Ω – OPEN)
2.31 S – 0 S
(432.9 m Ω – OPEN)
9.24 S – 0 S
(108.22 m Ω – OPEN)
L 0.231 S – 0 S
(4.329
Ω – OPEN)
0.461 S – 0 S
(2.1692 Ω – OPEN)
1.399968 S – 0 S
(714.30 m Ω – OPEN)
0.231 S – 0 S
(4.329
Ω – OPEN)
0.924 S – 0 S
(1.0822 Ω – OPEN)
Resolution Range H 400 μS 800 μS 2.424 mS 400 μS 1.6 mS
M 40 μS 80 μS 242.4 μS 40 μS 160 μS
L 4 μS 8 μS 24.24 μS 4 μS 16 μS
Accuracy of
setting
* 2
Range H, M ±(0.5 % of set * 3 + 0.5 % of f.s * 4 ) + Vin/500 k Ω
L ±(0.5 % of set * 3 + 0.5 % of f.s)
CV mode
Model PLZ164W PLZ334W PLZ1004W PLZ164WA PLZ664WA
Operating
range Range H 1.5 V – 150 V 0 V – 150 V
L 1.5 V – 15 V 0 V – 15 V
Setting range Range H 0 V – 157.5 V
L 0 V – 15.75 V
Resolution Range H 10 mV
L 1 mV
Accuracy of setting Range H,L ±(0.1 % of set + 0.1 % of f.s)
Input current variation * 1 12 mV
CP mode
Model PLZ164W PLZ334W PLZ1004W PLZ164WA PLZ664WA
Operating
range Range H 16.5 W – 165 W 33 W – 330 W 100 W – 1000 W 16.5 W – 165 W 66 W – 660 W
M 1.65 W – 16.5 W 3.3 W – 33 W 10 W – 100 W 1.65 W – 16.5 W 6.6 W – 66 W
L 0.165 W – 1.65 W 0.33 W – 3.3 W 1 W – 10 W 0.165 W – 1.65 W 0.66 W – 6.6 W
Setting range Range H 0 W – 173.25 W 0 W – 346.5 W 0 W – 1050 W 0 W – 173.25 W 0 W – 693 W
M 0 W – 17.325 W 0 W – 34.65 W 0 W – 105 W 0 W – 17.325 W 0 W – 69.3 W
L 0 W – 1.7325 W 0 W – 3.465 W 0 W – 10.5 W 0 W – 1.732 5 W 0 W – 6.93 W
Resolution Range H 10 mW 10 mW 100 mW 10 mW 20 mW
M 1 mW 1 mW 10 mW 1 mW 2 mW
L 0.1 mW 0.1 mW 1 mW 0.1 mW 0.2 mW
Accuracy of
setting Range H, M ±(0.6 % of set + 1.4 % of f.s * 1 )
L ±(0.6 % of set + 1.4 % of f.s)
Specifications Unless specified otherwise, the specifications are for the following settings and conditions.
• The warm-up time is 30 minutes (with current flowing).
• After warm-up is complete, the PLZ-4W must be calibrated correctly according to the procedures given in the operation
manual in a 23 °C±5 °C environment.
• ** % of set denotes ** % of the input voltage, input current, or input power setting.
• ** % of f.s denotes ** % of the rated input voltage, rated input current, or rated input power.
• **% of rdg represents denotes ** % of the input voltage, input current, or input power reading.