Atec Chroma-62000H Series - Manual (Page 7)

Programming & Measurement Resolution
Voltage (Front Panel )
10 mV
Current (Front Panel) 10 mA
Voltage (Digital Interface) 0.002% of Vmax
Current (Digital Interface) 0.002% of Imax
Voltage (Analog Interface ) 0.04% of Vmax
Current (Analog Interface ) 0.04% of Imax
Remote Interface
Analog programming
Standard
USB Standard
RS232 Standard
RS485 Standard
GPIB Optional
Ethernet Optional
System bus(CAN) Standard for master/slave control
Programming Accuracy
Voltage (Front Panel and Digital Interface )
0.1% of Vmax
Current (Front Panel and Digital Interface ) 0.3% of Imax
Voltage (Analog Interface) 0.2% of Vmax
Current (Analog Interface) 0.3% of Imax
GPIB Command Response Time
Vout setting
GPIB send command to DC source receiver <20ms
Measure V&I Under GPIB command using Measure <25ms
Analog Interface (I/O)
Voltage and Current Programming inputs (I/P)
0-10Vdc / 0-5Vdc / 0-5k ohm / 4-20 mA of F.S.
Voltage and Current monitor output (O/P) 0-10Vdc / 0-5Vdc / 4-20mA of F.S.
External ON/OFF (I/P) TTL:Active Low or High(Selective)
DC_ON Signal (O/P) Level by user define. ( Time delay = 1 ms at voltage slew rate of 10V/ms.)
CV or CC mode Indicator (O/P) TTL Level High=CV mode ; TTL Level Low= CC mode
OTP Indicator (O/P) TTL: Active Low
System Fault indicator(O/P) TTL: Active Low
Auxiliary power supply(O/P) Nominal supply voltage : 12Vdc / Maximum current sink capability: 10mA
Safety interlock(I/P) Time accuracy: <100ms
Remote inhibit(I/P) TTL: Active Low
Series & Parallel Operation *1 Master / Slave control via CAN for 10 units up to 150KW. (Series: two units / Parallel: ten units )
Auto Sequencing(List Mode)
Number of program
10
Number of sequence 100
Dwell time Range 5ms - 15000S
Trig. Source Manual / Auto / External
Auto Sequencing (Step Mode)
Start voltage
0 to Full scale
End voltage 0 to Full scale
Run time 10ms - 99hours
Input Specification
AC input voltage 3phase , 3 wire + ground
208/220 Vac(operating range 187 -242 Vac) *2
380/400 Vac(operating range 342 - 440 Vac)
440/480 Vac(operating range 396 - 528 Vac) *2
AC frequency range 47-63 Hz
Max Current(each phase)
208/220 Vac 5KW Model:39A 10KW Model:66A 15KW Model:91A
380/400 Vac 5KW Model:22A 10KW Model:37A 15KW Model:50A
440/480 Vac 5KW Model:19A 10KW Model:32A 15KW Model:44A
General Specification
Maximum Remote Sense Line Drop Compensation
<100V model: 5% of full scale voltage per line(10% total)
>100V model :2% of full scale voltage per line (4% total)
Operating Temperature Rage 0°C ~ 50°C
Storage Temperature Rage -40°C ~ +85°C
Dimension (HxWxD) 132.8 x 428 x 610 mm / 5.23 x 16.85 x 24.02 inch
Weight
5KW Model : Approx. 23 kg / 50.66 lbs
10KW Model : Approx. 29 kg / 63.88 lbs
15KW Model : Approx. 35 kg / 77.09 lbs
gENEral SPEciFicatiONS
Note*1 : To parallel more than 5 units, please contact factory.
Note*2 : Call for availability.
All specifications are subject to change without notice. Please visit our website for the most up to date specifications.