Atec Agilent-6032A - Manual

This series of dc power supplies
take the place of multiple power
supplies on your test bench by
providing maximum power at
a variety of operating points.
They have ten-turn front panel
pots to allow precise local control.
These power supplies also may be
connected in auto-parallel or auto-
series with their corresponding
GPIB unit (6030 Series), as part
of a test system.
Supplemental Characteristics
for all model numbers
Remote Sensing: Up to 2 V drop in each
lead. Voltage regulation specification met
with up to 0.5 V drop, but degrades for
greater drops.
Modulation: (analog programming of
output voltage and current)
Input signal: 0 to 5 V or 0 to 4 k Ohms
Regulatory Compliance: Certified to
CSA556B; conforms to IEC 61010-1.
Size: 425.5 mm W x 132.6 mm H x 516.4 mm D
(16.75 in x 5.25 in x 20.33 in).
See page 99 for more details
Warranty: One year
Ordering Information
Opt 120 104 to 127 Vac, 47 to 63 Hz
Opt 220 191 to 233 Vac, 48 to 63 Hz
Opt 240 209 to 250 Vac, 48 to 63 Hz
* Opt 908 Rack-mount Kit (p/n 5062-3977)
* Opt 909 Rack-mount Kit with Handles.
(p/n 5062-3983)
Opt 0L2 Extra Standard Documentation Package
Opt 0B0 No documentation package
Opt J01
Stabilization for loads up to 10 Henries
Agilent Performance dc Power Supplies speed and accuracy for test optimization
S p e c i f i c a t i o n s
(at 0 ˚ to 55 ˚ C unless
otherwise specified)
Power Products Catalog 2002-2003 For more detailed specifications see the product manual at www.agilent.com/find/power
52
Save rack space by using fewer outputs
Reduce cost by using fewer power supplies
Control with external voltage
6010A, 6011A, 6012B, 6015A
Single-Output, Autoranging:
200 W and 1000 W
6010A 6011A 6012B 6015A
Number of outputs 1 1 1 1
GPIB No No No No
Output ratings
Voltage 0 to 200 V 0 to 20 V 0 to 60 V 0 to 500 V
Current 0 to 17 A 0 to 120 A 0 to 50 A 0 to 5 A
Maximum power
Watts 1,200 W 1,064 W 1,200 W 1,050 W
Autoranging output V1, I
1
200 V, 5 A 20 V, 50 A 60 V, 17.5 A 500 V, 2 A
V2, I
2
120 V, 10 A 14 V, 76 A 40 V, 30 A 350 V, 3 A
V3, I
3
60 V, 17 A 7 V, 120 A 20 V, 50 A 200 V, 5 A
Ripple and noise, 20 Hz to 20 MHz
Voltage rms 22 mV 8 mV 8 mV 50 mV
p-p 50 mV 50 mV 40 mV 160 mV
Current rms 15 mA 120 mA 25 mA 50 mA
Load regulation
Voltage 0.01%+ 5 mV 3 mV 5 mV 13 mV
Current 0.01%+ 10 mA 15 mA 10 mA 35 mA
Transient response time
10% step change
Time 2 ms 2 ms 2 ms 5 ms
Level 150 mV 100 mV 100 mV 200 mV
Supplemental Characteristics (Non-warranted characteristics determined by design that are
useful in applying the product)
Programming resolution
Voltage
50 mV 5 mV 15 mV 125 mV
Current 4.25 mA 30 mA 12.5 mA 1.25 mA
dc floating voltage ±550 V ±240 V ±240 V ±550 V
either terminal can be grounded
or floated from chassis ground
ac input current 100 Vac 24 A 24 A 24 A 24 A
120 Vac 24 A 24 A 24 A 24 A
220 Vac 15 A 15 A 15 A 15 A
240 Vac 14 A 14 A 14 A 14 A
Weight Net 16.3 kg (36 lb) 17.2 kg (38 lb) 16.3 kg (36 lb) 16.3 kg (36 lb)
Shipping 21.8 kg (48 lb) 22.7 kg (50 lb) 21.8 kg (48 lb) 21.8 kg (48 lb)
A line cord option must be specified.
See pages 93-98 for ordering information.
* Support rails required Accessories
1494-0060 Rack Slide Kit
E3663AC Support rails for
Agilent rack cabinets
V1
I1 I2 I3
Volts
P1
P2
P3
Amps
V2
V3
Autoranging Output: