Cla-Val 390-07/3690-07 - Manual (Page 21)

Page 2
32 Series Software Kit
For Operation A (above) applications, no changes to the 33
Series control preset values are needed. For Operation B (above)
applications, the 33 Series Software kit is used to ONLY change
factory-set values of: 1) range limits (high and low), 2) rotational
speed of actuator, and 3) loss of signal mode. It is used only for
set-up of 33 Series pilot controls during initial valve start-up or
during valve repair.
The Cla-Val 130VC-3 Software Kit is required to communicate
between your Windows XP laptop computer and 130VC-3
Actuator. It consists of a free software program, a special multi-
USB connector cable, and these instructions. The software is
obtained by downloading from our website. Only one cable is
needed to work with all 130VC-3 Actuators. Replacement cables
(p/n 20519203A) can be ordered at extra cost. ADAPTOR.
Do not use this software for remote control of 130VC-3 Actuator.
Software Download Instructions
Supported Operating Systems are Windows XP and XP Service Pack 2
1) Go to Cla-Val website (www.cla-val.com) and navigate to
33 Series actuator software download page. Click the
Download 130VC-3 Range Software button to start the
download.
2) Do one of the following:
_ To start the installation immediately, click RUN to run
this program from its current location.
_ To copy the download to your computer for installation
at a later time, click SAVE to save this program.
3) This program will automatically be installed in new e-Drive
folder in C: Program Files/Cla-Val folder on your computer.
A new Cla-Val folder is created in Program Files folder and
an "e-Drive" icon link is created on Desktop to start program.
33 Series Actuator and Software Set-up
Change 130VC-3 Actuator configuration from factory default set-
tings, by using free download software from website (www.cla-
val.com). To set up a communication link with 130VC-3 Actuator,
first install software and cable driver and then special USB commu-
nications cable in laptop computer. After installing driver and com-
munication cable, the actuator must be powered for link to work.
Follow hardware set-up and wiring diagram instructions. Your com-
puter must be on before powering the actuator.
Hardware set-up steps must be completed before program will
communicate and change 130VC-3 factory default settings. Until
wiring and power connections are made to the actuator, the soft-
ware program can be opened, but new parameters can not be cre-
ated or stored or sent to actuator. Changes to parameters must be
done "live" and while control valve is operating.
Cla-Val multi-USB Driver Setup
When 130VC-3 communications cable is installed in your laptop
computer USB port for the first time, Windows will search your
computer for the cable multi-USB driver. If Windows Plug-and-
Play does not automatically find the driver and connect to actuator,
then the cable driver must be set-up manually. Use the following
instructions to manually activate the cable driver.
Download multi-USB software from the Cla-Val web site:
www.cla-val.com
Connect the USB cable to the laptop.
Select: "Install from a list or specific location".
Browse to file: C\Program Files\CLA-VAL\Multi-USB Driver Setup.
Microsoft validation presss “Continue Anyway”
Welcome to the Hardware Update
Wizard
This wizard helps you install software for:
USB Device
If your hardware came with an installation CD or
floppy disk, insert it now.
What do you want the wizard to do?
Install the software automatically (Recommended)
Install from a list or specific location (Advanced)
Click Next to continue
Hardware Update Wizard
Next > Cancel < Back
Donʼt search. I will choose the driver to install
Choose this option to select the device driver from a list. Windows does not guarantee that the
driver you choose will be the best match for your hardware
Hardware Update Wizard
Next > Cancel < Back
Search for the best driver in these locations
Use the check boxed below to limit or expand the default search, which includes local paths and
removable media. The best driver found will be installed.
Search removable media (floppy, CD-Rom...)
Include this location in the search
Please choose your search and installation options.
C:\Program Files\CLA-VAL\Muliti-USB Driver Setup Browse
Completing the Hardware Update
Wizard
This wizard has finished installing the software for
Cla-Val Multi-USB Interface
Click Finish to close the wizard
Hardware Update Wizard
Continue Anyway STOP Installation
The software you are installing for this hardware
CLA-VAL Muliti-USB Interface
has not passed Windows Logo Testing to verify it compatbility with
Windows XP. (
Tell me why this testing is important )
Continuing your installation of this software may impair or
distabilize the correct operation of your system either
immediately or in the future. Microsoft strongly recommends
that you stop this installation now and contact the hardware
vendor for software that has padded Windows Logo testing.
!