Buyers LT12 - Manual

Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
Installation Instructions
1 3004444 2 Base Weldment, Trimmer Rack, LT12
2 0204300 4 Plug, Plastic Finish, 1" Sq Tube
3 3004083 6 Guide, Spring
4 3004084 6 Spring, Torsion Trimmer Rack
5 3005286 3 Hook, Grip Pivot
6 - 6 Screw, HHC 5/16-18 x 2-3/4 Gr 5 Zn
7 - 6 Nut, Nylock 5/16-18 Zn
8 3004082 3 Hook, Pivot
9 - 8 Washer, Flat 3/8" SAE Zn
10 - 8 Screw, Hex Head Lag, 3/8 x 1-1/4 Zn
ITEM PART NO. QTY. DESCRIPTION
Bill of Materials
LT12 Trimmer Rack
for Enclosed Landscape Trailers
Important!
Before you begin installing:
1. Read and understand these instructions completely.
2. Verify that you have received all the parts listed in the
bill of materials.
CAUTION:
Always wear safety glasses when using power tools.
Tools and Materials Required:
•9/16" Wrench or Socket
•Electric Drill
•1/4" Drill Bit
•3/4" Plywood Shim Strips
•Shim Screws
1. Locate a suitable place on the wall to mount the trimmer
rack. The two racks should be mounted 28" to 34" apart. The
large hook on the one upright should engage the trimmer’s
grip and the smaller hooks on the other upright should
engage the shaft of the trimmer.
Do not clamp on or near
the throttle trigger of the trimmer. Verify the determined
positions will work with all the trimmers you wish to mount
in the rack. Bent shaft trimmers require the brackets to be
mounted closer together than straight shaft trimmers.
2. In order to mount this rack to the enclosed trailer, you
must first add 3/4" plywood shim strips to the walls.
These shim strips must be attached to at least two wall
support studs with suitable fasteners. If you don’t know
what kind or length of fastener to use contact your trailer
dealer or manufacturer for their recommendation.
3. Hold the trimmer racks against the shims, hold level, and
mark the position of the four 3/8" holes in each rack. Make
sure that the two racks are in line with each other and are
at the proper spacing.
WARNING! Check for locations of brake lines and
electrical wiring etc., before drilling any holes. Any
damage to trailer during installation is the installer’s
sole responsibility.
4. Drill eight 1/4" pilot holes in the positions just marked
for the 3/8" lag screws. Be extremely careful not to drill
through the outside trailer wall.
5. Fasten the racks to the trailer wall with the eight 3/8"
x 1-1/4" lag screws and eight 3/8" flat washers supplied.
WARRANTY
Buyers Products Co. warrants all truck/trailer hardware manu-
factured or distributed by it, to be free from defects in material
and workmanship for a period of one year from date of shipment.
Parts must be pro-perly installed and used under normal condi-
tions. Any product which has been altered, including modification,
misuse, accident or lack of maintenance will not be considered
under warranty. Normal wear is excluded. The sole responsi-
bility of Buyers Products Co. under this warranty is limited to
repairing or replacing any part or parts which are returned, pre-
paid, and are found to be defective by Buyers Products Co.
Authorization from Buyers Products Co. must be obtained before
returning any part. No charges for transportation or labor per-
formed on Buyers’ products will be allowed under this warranty.
3004481 Rev. B