Led undercar kit – StreetGlow Single Color LED Undercar Kit User Manual

Page 2

Step 1 Unpack entire contents of packaging and check for any damaged products before moving to the testing sequence.

Step 2 Place all 4 LED tubes on a test bench and connect the 4 LED control wires of the tubes to the back of the

Digital LED Controller (DLC).

Step 3 Using a 12v DC power source, connect the DLC’s RED and YELLOW (Power) wires to the Positive (+) 12v

lead of the power supply. Note: DO NOT connect the BLUE (Alarm) wire for this test.

Step 4 Next connect the DLC’s BLACK (Ground) wire to the power supply’s Negative (-) output

Step 5 Press the Power ON/OFF button to activate all LED segments – ON. Note: If none of the LED’s light up, then

go back to Step 3 and check your connections for Power and Ground.

2 - 48” LED tubes
2 - 30” LED tubes
1 - Digital LED Controller (DLC)

14 - 3/4” tube mounting clamps
12 - 3/16” wire clamps
26 - 5/8” self-tapping screws

PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING!

Quick Test Sequence

Step 1 Select a desired location for the Digital LED Controller (DLC) and mount using the supplied mounting hardware.

Step 2 With DLC mounted connect power and ground to the DLC’s power harness as shown in wiring connection diagram.

• YELLOW wire = 12v Battery (+)
• RED wire = 12v Ignition (+)
• BLACK Wire = Negative ground (-)
• BLUE wire = Alarm Negative input (-) (optional connection)
Note: Vehicles with after market alarms can use the ANLED100’s Alarm feature to activate when
Ignition Kill is enabled with a Negative trigger.

Step 3 Select the desired locations for the LED tube placement which are away from all fuel lines, exhaust systems,

areas of extreme heat, ABS components, SRS components, any moving parts and where lifts or jacks are
used to raise your vehicle. Note: LED tubes need to be mounted as to the recommended configuration
(see FIGURE 1 for details).

Step 4 Using the 3/4” tube mounting clamps and the 5/8” self-tapping screws, fasten the LED tubes to your

vehicle in the recommended mounting positions (4 mounting clamps per 48” tube, 3 clamps per 30” tube).

Step 5 Run the control wires from each LED tube underneath the vehicle up into the DLC location. It’s recommended

to run all wires in the shortest path to the DLC away from all fuel lines, exhaust systems, areas of extreme
heat, ABS components, SRS components, any moving parts, and where lifts or jacks are used to raise your vehicle.

Step 6 With all 4 control wires located at the DLC, plug each LED tube control wire into the back of the DLC

outputs (see FIGURE 1 for details).

Step 7 Once wiring and mounting for all components is completed, test the ANLED100’s 3 modes of operation

and the sequential lighting effects.

Installation Instructions

Step 1 Turn unit ON by pressing and holding ON/OFF button for 2 seconds

Step 2 Turn unit OFF by pressing and holding ON/OFF button for 2 seconds

Digital LED Controller (DLC) Operation

MODES: All LED’s On / Music Interface / Sequential Lighting Effects

Turn unit ON and select the desired MODE of operation by using the following steps:

Step 1 1st press MODE button = All LED’s On mode (solid show of lights)

2nd press MODE button = Music Interface mode (dances to the beat of your music)
3rd press MODE button = Sequential Lighting Effect mode (see FIGURE 2 for different effects)
• Alarm Mode = Activates when the BLUE wire is triggered with a Negative (ground) input
• This feature functions ONLY when the vehicle is off or when 12v is disconnected from the Ignition RED

wire (see FIGURE 1 for details)

• When the Alarm mode is active, the 3rd (middle) bank of LED’s will flash once per second under the vehicle

Step 2 Selecting different light shows

• When the DLC is in Sequential Lighting mode, you’re able to select up to 8 different lighting effects by pressing

the SEQ. button 3 times (see FIGURE 2 for details)

• To increase the speed of light, press and hold the SPEED button until desired effect is achieved
• To decrease the speed of light, press twice and hold the SPEED button until desired effect is achieved

Step 3 Enjoy!

Modes and Sequential Lighting Effects

Controller

BLACK (-)

YELLOW (+)

BATTERY

ALTERNATIVE POWER SOURCE

(IE: FUSEBOX)

Ground

Alarm

BLUE (-)

Ground

(Optional)

RED (+)

IGNITION

CENTER OUT

OUT CENTER

NIGHT CRUZIN'

RIGHT TO LEFT

LEFT TO RIGHT

INCH WORM

ALL FLASH

FIGURE

LED UNDERCAR KIT

I N S T A L L A T I O N

I N S T R U C T I O N S

FRONT

REAR

WIRING DIAGRAM