StreetGlow OPTX Multi Color LED Undercar kit User Manual
Page 2
Step 1 Unpack entire contents of package and check for any damaged products before moving to the test sequence.
Step 2 Place all four LED tubes on a test area. Connect the wires together and connect them to the Multi-Color LED
Controller (MLC). NOTE: Be sure to align the arrows on the plugs.
Step 3 Using a 12v DC power source, connect the MLC’s RED and YELLOW (power) wires to the positive (+) 12v
lead of the power source. NOTE: DO NOT connect the BLUE (alarm) wire for this test.
Step 4 Connect the MLC’s BLACK (ground) wire to the power supply’s negative (-) output.
Step 5 Press and hold the ON/OFF button to activate all LED segments. NOTE: If none of the LED’s light up, then
go back to Step 2 and check your connections.
CONTENTS:
2 - 48” Tubes
1 - 30” Tube w/ 4’ wire
1 - 30” Tube w/ two 4’ wires
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING!
Quick Test Sequence
Step 1 Select the desired location for the Multi-color LED Controller (MLC) and mount using the supplied mounting hardware.
Step 2 With the MLC mounted make connections of power and ground to the MLC’s power harness (see FIGURE 1).
YELLOW wire = (+) 12v battery
RED wire = (+) 12v ignition
BLACK wire = (-) ground
BLUE wire = (-) alarm (optional connection)
NOTE: Vehicles with aftermarket alarms can use the OPLED100MC’s alarm feature to activate when
Ignition Kill is enabled with a negative trigger.
Step 3 Select the desired locations for the LED tube placement which are away form all fuel lines, exhaust systems,
areas of extreme heat, ABS components, SRS components, any moving parts and where lifts or jacks are
used to raise your vehicle (see FIGURE 1 for details).
Step 4 Using the 3/4" tube mounting clamps and the 5/8” self-tapping screws, fasten the LED tubes to your vehicle
in the recommended mounting positions (4 mounting clamps per 48” tube, 3 clamps per 30” tube).
Step 5 Connect the control wires of each tube together. Secure the wires to your vehicle using the 3/16” wires
clamps and 5/8” screws. NOTE: Be sure to align the arrows on the plugs and use electrical tape (not supplied)
around the secured plugs to insure a proper weather-tight connection.
Step 6 Run the control wire of the MLC to the control wire of the first LED tube and make proper connection
(See FIGURE 1 for correct tube placement).
Step 7 Once the wiring and mounting of all components are completed, test the OPLED100MC’s modes of operation
and sequential lighting effects.
Installation Instructions
1 Turn unit on by pressing and holding ON/OFF button for 2 seconds
2 Turn unit off by pressing and holding ON/OFF button for 2 seconds
3 Change color by pressing COLOR button
4 Increase Brightness/Speed/Sensitivity by pressing + button
5 Decrease Brightness/Speed/Sensitivity by pressing – button
Multi-Color LED Controller (MLC) Operation
LED UNDERCAR KIT
I N S T A L L A T I O N
I N S T R U C T I O N S
1
MULTI-COLOR
1 - Multi-color LED Controller (MLC)
14 - 3/4” Tube mounting clamps
12 - 3/16” Wire clamps
26 - 5/8” Self-tapping screws
MODES: All LED’s On / Music Interface / Sequential Lighting Effects/ Color Change
Step 1 SELECTING MODE OF OPERATION
1st press MODE button = All LED’s On mode (solid show of lights)
2nd press MODE button = Music Interface mode (dances to the beat of your music)
NOTE: Use the +/– buttons to adjust the sound sensitivity
3rd press MODE button = Sequential Lighting Effect mode (see FIGURE 2 for different effects)
• Alarm Mode = Activates when the BLUE wire is triggered with a negative input (ground)
• This feature functions ONLY when the vehicle is off or when 12v is disconnected from the RED wire (ignition)
(see FIGURE 1 for details)
• When the Alarm Mode is active, the 3rd (middle) bank of LED’s will flash once per second under the vehicle
Step 2 SELECTING LIGHTING EFFECTS
• When the MLC is in Sequential Lighting Effects mode, you are able to scroll through eight different lighting
effects by pressing the MODE button (see FIGURE 2 for details)
• To increase the speed of light, press and hold the + button until desired effect is achieved
• To decrease the speed of light, press and hold the – button until desired effect is achieved
Step 3 SELECTING COLORS
Press the COLOR button to switch between 1 of 7 available colors. The center LED of the MLC will indicate
the selected color. NOTE: The first time the kit is powered up, it will be WHITE.
AUTO-CHANGE (cycles through all colors), RED, YELLOW, GREEN, TURQUOISE,
NEO BLUE, PURPLE, WHITE
Step 4 Enjoy!
Modes and Sequential Lighting Effects
-
+
BATTERY
OR
ALTERNATIVE POWER SOURCE
(IE: FUSEBOX)
Ground
Red = 12v Ign. (+)
Yellow = 12v Batt. (+)
Blue = Alarm (-)
Black = Ground (-)
Mini Din
Connection
Mini Din
Connection
Mini Din
Connection
(optional feature)
MLC (Mount Under Dash)
Mini Din
Connection
CENTER OUT
OUT CENTER
NIGHT CRUZIN'
1
2
RIGHT TO LEFT
LEFT TO RIGHT
DOUBLE STEP
ALL FLASH
FIGURE
1
FIGURE
2
FRONT
REAR
WIRING DIAGRAM
2