dbx DriveRack 260 - Manual (Page 49)

DriveRack
®
41 DriveRack® User Manual
Section 5
To set the PUP Program option use the following procedure:
• From Program mode, press the UTILITY button and use the PREV PG or NEXT PG
buttons to move to the page that appears as follows:
Utility
LCD Contrast 10
Auto EQ Plot RTA
Power Up Modes
PUP Program Stored
PUP Mute Current
ZC Setup
Panel 1 None
(STORE) - EDIT PANEL
Panel 1 ZC-2
Boost 0dB Cut 0dB
Output 1 3 5
2 4 6
Set Security Level
Pre EQ
Low
Set 260 Device Level
High
Password
Enter Password
Password
Edit High Password
Edit Med Password
Press Store to Change
Press Store
Program List
List Size 10
List Index 1
Program 1
Prog Change Mode
Program List
Prog Lock 24
Output Jumpers
Output 1
Setting 30
Panel 1 ZC-3
Select A
No Change
Panel 1 ZC-4
Switch
No Change
1 2 3 4
- SELECT CHARACTER
- LEFT/RIGHT:
-SAVE/-EXIT
NAME: R OCK VENUE
- SELECT CHARACTER
- LEFT/RIGHT:
-SAVE/-EXIT
NAME:
• With the arrow next to the PUP Program option, turn the DATA wheel to make the
desired selection.
To change the PUP Mute setup, use the following procedure:
• From Program mode, press the UTILITY button and use the PREV PG or NEXT PG
button to move to the page that appears as follows:
Utility
LCD Contrast 10
Auto EQ Plot RTA
Power Up Modes
PUP Program Stored
PUP Mute Current
ZC Setup
Panel 1 None
(STORE) - EDIT PANEL
Panel 1 ZC-2
Boost 0dB Cut 0dB
Output 1 3 5
2 4 6
Set Security Level
Pre EQ
Low
Set 260 Device Level
High
Password
Enter Password
Password
Edit High Password
Edit Med Password
Press Store to Change
Press Store
Program List
List Size 10
List Index 1
Program 1
Prog Change Mode
Program List
Prog Lock 24
Output Jumpers
Output 1
Setting 30
Panel 1 ZC-3
Select A
No Change
Panel 1 ZC-4
Switch
No Change
1 2 3 4
- SELECT CHARACTER
- LEFT/RIGHT:
-SAVE/-EXIT
NAME: R OCK VENUE
- SELECT CHARACTER
- LEFT/RIGHT:
-SAVE/-EXIT
NAME:
• Select the PUP Mute option by pressing the DATA wheel until PUP Mute is selected.
Once the PUP Mute option has been selected, proceed to rotate the DATA wheel until
the desired mute setting is selected. To exit, press the PROGRAM/CONFIG button.
5.1.3 ZC Setup
A unique feature of the DriveRack 260 is its ability to interface with dbx proprietary Zone
Controller wall-panels. This feature gives you the ability to control various parameters of
the 260 such as Output Levels, Mute and Program Changes. Up to six ZC panels can be
connected to a DriveRack 260. To program a ZC panel, proceed with the following instructions.
• From Program mode, press the UTILITY button and use the PREV PG or NEXT PG
button to move to the page that appears as follows:
Utility
LCD Contrast 10
Auto EQ Plot RTA
Power Up Modes
PUP Program Stored
PUP Mute Current
ZC Setup
Panel 1 None
(STORE) - EDIT PANEL
Panel 1 ZC-2
Boost 0dB Cut 0dB
Output 1 3 5
2 4 6
Set Security Level
Pre EQ
Low
Set 260 Device Level
High
Password
Enter Password
Password
Edit High Password
Edit Med Password
Press Store to Change
Press Store
Program List
List Size 10
List Index 1
Program 1
Prog Change Mode
Program List
Prog Lock 24
Output Jumpers
Output 1
Setting 30
Panel 1 ZC-3
Select A
No Change
Panel 1 ZC-4
Switch
No Change
1 2 3 4
- SELECT CHARACTER
- LEFT/RIGHT:
-SAVE/-EXIT
NAME: R OCK VENUE
- SELECT CHARACTER
- LEFT/RIGHT:
-SAVE/-EXIT
NAME:
Important Note: The dip switches on the ZC panel(s) must match the Panel (ID) number
displayed in this page.
Utilities/Meters