GE P&W Pleated Filters - Memtrex NY Pleated Filters - Manual (Page 2)

Page 2 FS1092EN
Table 3: Operational Limits
Description Operational Limits
Maximum Forward Differen-
tial Pressure
60 psi (4.1 bar) at 70ºF (21ºC)
Maximum Reverse Differen-
tial Pressure
30 psi (2.1 bar) at 70ºF (21ºC)
Maximum Operating Tem-
perature
180ºF (82ºC) at 10 psid
(0.7 bar) in water
Table 4: Integrity Testing
Micron Rating Specification
0.1 µm ≤ 50 cc/min at 40 psig (2.76 bar)
0.2 µm ≤ 50 cc/min at 30 psig (2.07 bar)
0.45 µm ≤ 50 cc/min at 15 psig (1.03 bar)
0.65 µm ≤ 50 cc/min at 12 psig (0.83 bar)
1.0 µm ≤ 50 cc/min at 5 psig (0.34 bar)
Air diffusion per 10” module after saturation with clean water
Table 5: Flow Performance in Clean Water 1
1 Data based on 10” length filter
Additional Information
• Memtrex NY filters may be autoclaved or in situ
steam sterilized (up to 257°F [125°C], 30-minute
cycles) for a maximum accumulated exposure
of 10 hours. Alternately, the filters may be sani-
tized with compatible chemical agents.
• GE certifies that the material contained in its
Memtrex NY pleated filters meet U.S. FDA re-
quirements for food contact under the applica-
ble regulations in 21 CFR. For further
information, contact GE technical services.
Memtrex NY filters meet the test criteria for USP
class VI-121°C Plastics.
• Aqueous extracts from Memtrex NY filters con-
tain less that 0.25 EU/ml. The filters typically ex-
hibit low levels of non-volatile residues.
• GE filter cartridges are designed and manufac-
tured for resistance to a wide range of chemical
solutions. Conditions will vary with each appli-
cation and users should carefully verify chemi-
cal compatibility. Please contact your GE
distributor for more information.
• Table 6 provides additional ordering information.
Table 6: Ordering Information
Type Micron Rating
Nominal Cartridge
Length End #1 Adapter End #2 Adapter Elastomer Material
MNY 91 = 0.1 µm
92 = 0.2 µm
94 = 0.45 µm
96 = 0.65 µm
01 = 1.0 µm
1 = 10 in. (25.4 cm)
2 = 20 in. (50.8 cm)
3 = 30 in. (76 cm)
4 = 40 in. (101.5 cm) A = Open End Gasket
B = 120 O-Ring
C = 213 O-Ring
E = 222 O-Ring
F = 226 O-Ring
J = 020 O-Ring
Q = 222 O-Ring
Stainless Steel Insert
Z = 226 O-Ring
Stainless Steel Insert
A = Open End Gasket
B = 120 O-Ring
C = 213 O-Ring
G = Closed End Cap
H = Fin Adapter
B = Buna-N
E = EPDM
S = Silicone
T = Teflon
2
Encapsulated
(Only in 222
and 226 Sizes
V = Viton 2
2 Teflon and Viton are registered trademarks of DuPont.