GE P&W Spiral Wound Membranes - JX Series - Manual

Find a contact near you by visiting www.gewater.com and clicking on “Contact Us” .
* Trademark of General Electric Company; may be registered in one or more countries.
©2013, General Electric Company. All rights reserved.
AM-FSpwJXSeries_EN Nov-13
Fact Sheet
JX Series
Industrial Stream Clarification MF Element
The J-Series family of microfiltration membrane el-
ements is used for process stream clarification in-
cluding suspended solids removal.
The J-Series membrane is manufactured with a
pore-size of 0.3 micron.
Table 1: Element Specification
Membrane J-Series, Polyvinylidene Fluoride
Model
Spacer
mil (mm)
Active
mrea
ft 2 (m 2 )
Outer wrap
Part
number
JX2540F30 30 (0.76) 28 (2.6) Fiberglass 1207253
JX2540F50 50 (1.27) 19 (1.8) Fiberglass 1207252
JX4040C30 30 (0.76) 73 (6.8) Cage 1207264
JX4040F30 30 (0.76) 91 (8.5) Fiberglass 3049975
JX4040F50 50 (1.27) 62 (5.8) Fiberglass 3049974
JX8040F30 30 (0.76) 366 (34.0) Fiberglass 1207283
JX8040F50 50 (1.27) 273 (25.4) Fiberglass 1207284
Figure 1: Element Dimensions Diagram - Female
Figure 2: Element Dimensions Diagram – Male
Table 2: Dimensions and Weight
Model 1
Dimensions, inches (cm) Boxed
A B 2 C 3
Weight
lbs (kg)
JX2540F30
40.0
(101.6)
0.75
(1.9) OD
2.4
(6.1)
4
(1.8)
JX2540F50
40.0
(101.6)
0.75
(1.9) OD
2.4
(6.1)
4
(1.8)
JX4040C30
40.0
(101.6)
0.625
(1.59)
3.9
(9.9)
9
(4.1)
JX4040F30
40.0
(101.6)
0.75
(1.9) OD
3.9
(9.9)
9
(4.1)
JX4040F50
40.0
(101.6)
0.75
(1.9) OD
3.9
(9.9)
9
(4.1)
JX8040F30
40.0
(101.6)
1.125
(2.86)
7.9
(20.0)
29
(13.2)
JX8040F50
40.0
(101.6)
1.125
(2.86)
7.9
(20.0)
29
(13.2)
1 These elements are bagged dry before shipping.
2 Internal diameter unless specified OD (outside diameter).
3 The element diameter (dimension C) is designed for optimum performance in GE
pressure vessels. Other pressure vessel dimension and tolerance may result in
excessive bypass and loss of capacity.
Table 3: Operating and CIP parameters
Typical Operating Flux 5-20 GFD (8-34 LMH)
Maximum Operating Pressure 100psi (700kPa)
Maximum Temperature Continuous Operation: 122°F (50°C)
Clean-In-Place (CIP): 122°F (50°C)
pH Range Continuous Operation: 2.0-10.0
Clean-In-Place (CIP): 1.0-11.5
Maximum Pressure Drop Over an element: 15psi (103kPa)
Per housing: 60psi (414kPa)
Chlorine Tolerance 5,000+ ppm-days