beautypg.com

GE P&W Spiral Wound Membranes - AG HR Series User Manual

Ag hr seri, High rejection brackish water ro elements, Fact sheet

background image

Fact Sheet

AG HR Seri

e

s

High Rejection Brackish Water RO Elements

The A-Series family of proprietary thin-film reverse
osmosis membrane is characterized by high flux
and high sodium chloride rejection. AG HR brackish
water elements are selected when high rejection
and operating pressures as low as 200 psi (1,379
kPa) are desired. These elements are recommended
for brackish water with salt concentration (TDS) lev-
els between 1,000 and 10,000mg/l or when very
high salt rejection of monovalent ions is required.

Find a contact near you by visiting www.ge.com/water and clicking on “Contact Us”.

* Trademark of General Electric Company; may be registered in one or more countries.

©2011, General Electric Company. All rights reserved.

FSpwAGHRSeries_EN Feb-11

Table 1: Element Specification

1

Average salt rejection after 24 hours operation. Individual flow rate

may vary +25%/-15%.

2

Testing conditions: 2,000ppm NaCl solution at 225psi (1,550kPa) oper-

ating pressure, 77°F (25°C), pH7 and 15% recovery.

Model

Active area

ft

2

(m

2

)

Outer wrap

Part

number

AG-90

90 (8.4)

Fiberglass

3056665

AG-365

365 (33.9)

Fiberglass

3056666

AG-400

400 (37.2)

Fiberglass

3056667

AG-400, 34

400 (37.2)

Fiberglass

3056668

AG-440

440 (40.9)

Fiberglass

3056669

AG-1600

1600 (148.6)

Fiberglass

3056670

Table 2: Operating and CIP parameters

3

SDI is measured on a non-linear scale using a 0.45 micron filter paper.

Additionally, finer colloids, particulates and microorganisms that pass
through the filter paper and not measured in the SDI test, will poten-
tially foul the RO element. For performance consistency and project
warranty, please use Winflows projection software and consult your
Filters with Membranes representative.

Figure 1a: Element Dimensions Diagram – Male



Figure 1b: Element Dimensions Diagram – Female




Membrane

Thin-film membrane (TFM*)

Model

Average

permeate flow

gpd (m3/day)

1,2

Average

NaCl

rejection

1,2

Minimum

NaCl

rejection

1,2

AG-90

2200 (8.3)

99.8%

99.3%

AG-365

9600 (36.3)

99.8%

99.3%

AG-400

10500 (39.7)

99.8%

99.3%

AG-400, 34

10500 (39.7)

99.8%

99.3%

AG-440

11500 (43.5)

99.8%

99.3%

AG-1600

42000 (159.0)

99.8%

99.3%

Typical Operating Pressure

200 psi (1,380 kPa)

Typical Operating Flux

10-20GFD (15-35LMH)

Maximum Operating Pressure 600 psi (4,137 kPa)

Maximum Temperature

Continuous operation: 122°F (50°C)
Clean-In-Place (CIP): 122°F (50°C)

pH range

Optimum rejection: 7.0-7.5,
Continuous operation 4.0-11.0,
Clean-In-Place (CIP): 2.0-11.5

Maximum Pressure Drop

Over an element: 12 psi (83 kPa)
Per housing: 50 psi (345 kPa)

Chlorine Tolerance

1,000+ ppm-hours,
dechlorination recommended

Feedwater

3

NTU < 1
SDI < 5

Table of contents