Flight & shield assembly, Assembly – Grain Systems Unload Augers PNEG-1050 User Manual

Page 19

12" & 14" Commercial Bin Sweep Augers PNEG-1050

Assembly

3. FLIGHT & SHIELD ASSEMBLY

1st Section

12"

w/ cutback 2nd Section 3rd Section

4th Section

5th Section

6th Section

Catalog

Bin

attached

from from from from from

Number

Diameter

Drive unit

GCS14360

24'

9'- 9 3/4"

6' - 7 1/2"

GCS14370

37'

9'- 9 3/4"

7' - 1 1/2"

GCS14400

40'

9'- 9 3/4"

8' - 7 1/2"

GCS14420

42'

9'- 9 3/4"

9' - 3 1/2"

GCS14430

43'

9'- 9 3/4"

9' - 9 3/4"

GCS14480

48'

9'- 9 3/4"

7' - 1 1/2"

5'- 3 1/2"

GCS14490

49'

9'- 9 3/4"

8'- 10"

3' - 9 1/2"

GCS14540

54'

9'- 9 3/4"

8'- 10"

6' - 7 1/2"

GCS14550

55'

9'- 9 3/4"

8'- 10"

7' - 1 1/2"

GCS14590

59'

9'- 9 3/4"

9'- 3 1/2"

8' - 7 1/2"

GCS14600

60'

9'- 9 3/4"

9' - 9 3/4"

8' - 7 1/2"

GCS14620

62'

9'- 9 3/4"

9' - 3 1/2"

9'- 3 1/2"

GCS14680

68'

9'- 9 3/4"

6' - 7 1/2"

8'- 10"

6'- 7 1/2"

GCS14720

72'

9'- 9 3/4"

7' - 1 1/2"

9'- 9 3/4"

7'- 1 1/2"

GCS14750

75'

9'- 9 3/4"

7' - 1 1/2"

9'- 3 1/2"

GCS14780

78'

9'- 9 3/4"

9' - 3 1/2"

9'- 3 1/2"

8' - 7 1/2"

GCS14800

80'

9'- 9 3/4"

9' - 9 3/4"

9'- 9 3/4"

8' - 7 1/2"

GCS14880

88'

9'- 9 3/4"

6' - 7 1/2"

8' - 10"

6' - 7 1/2"

9' - 9 3/4"

GCS14900

90'

9'- 9 3/4"

3' - 9 1/2"

9'- 9 3/4"

9' - 3 1/2"

9' - 9 3/4"

GCS14920

92'

9'- 9 3/4"

7' - 1 1/2"

8' - 10"

GCS14105

105'

9'- 9 3/4"

5' - 3 1/2"

9'- 9 3/4"

9' - 9 3/4"

5' - 3 1/2"

GCS14113

113'

9'- 9 3/4"

8'- 10"

9'- 9 3/4"

8' - 10"

9' - 9 3/4"

6' - 7 1/2"

GCS14120

120'

9'- 9 3/4"

9' - 3 1/2"

9'- 9 3/4"

9' - 9 3/4"

8' - 7 1/2"

Sweep Flight and Back Shield Sections

A Commercial Bin Sweep can be made up of several
sections of flighting and back shields. The quantity and
lengths of the sweep flight and back shield sections will
vary depending on the bin size. Use the chart below for the
number and length of sections for your size of bin.

The sweep flight with a cut back must connect to the drive
assembly. The remaining sections should be assembled in
the order shown in the chart below. The section furthest
from the drive has mounting holes for the sweep tractor.

The assembly instructions in this section cover assem-
bling the complete Commercial Sweep. Refer to pages 30-
33 and read where use of only a part of the sweep auger

may be recommended when starting to sweep unload a
bin, particularly a large bin. You may choose to only
assemble one or two sections of sweep flight, back
shields, and bearing stands for initial sweep unloading.
Remember, any number of sweep sections can be used
together up to a maximum of six. If a sweep auger with
four or more sections was selected, a truss assembly is
included. The truss should be used when four or more
sections are assembled together. Refer to page 24 for
truss assembly instructions. If the truss assembly you
have is for a greater number of sweep auger sections
than you are assembling, be sure to tie off the extra
cable length so it does not become entangled in the
sweep auger.