Yamaha RX-V3800 - Manual (Page 93)

89
En
Graphical user interface (GUI) screen
AD
V
ANCED
OPERA
T
ION
English
Use this menu to adjust the video parameters.
1
Set the operation mode selector to D
AMP
and then press G
SET MENU on the remote
control.
2
Press 4k / n / l / h on the remote control to
select “Manual Setup” and then press 4h.
3
Press 4k / n / l / h on the remote control to
select “Video” and then press 4h.
4
Select the desired parameters and then press
4h to access and adjust.
Use the “Video” in “Initialize” to set the parameters in “Manual
Setup (Video)” (except “Short Message” and “On Screen”) to the
factory presets (see page 126).
■ Conversion (Video conversion)
Use this feature to activate or deactivate the video scaling
as well as the HDMI up-conversion of the analog video
signals input at the composite VIDEO, S VIDEO, and
COMPONENT VIDEO jacks.
• This unit does not convert 480 line video signals and 576 line
video signals interchangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted into the S-video or composite
video signals and output at the S VIDEO MONITOR OUT and
VIDEO MONITOR OUT jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of video connections between each component.
• When composite video or S-video signals from a VCR are
converted into component video signals, the picture quality may
suffer depending on your VCR.
• Even when “Conversion” is set to “On”, HDMI digital signals
are not converted to analog video signals.
• If “Conversion” is set to “Off”, the “Component I/P”, “HDMI
Resolution”, “HDMI Aspect”, and “Short Message” features
are deactivated.
• Set “Conversion” to “On” to display the short message.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set “Conversion” to “Off”.
• When non-standard video signals (such as video signals from a
video game console) are input, this unit does not display short
messages on the video monitor even if “Conversion” is set to
“On”.
• When the analog component video signals with 480p of
resolution are input at the COMPONENT VIDEO jacks and the
video monitor is connected to the VIDEO MONITOR OUT or
S VIDEO MONITOR OUT jack of this unit, the GUI screen is
not displayed on the video monitor.
• This unit does not up-scale the analog component video signals
with 720p or 1080i of resolution.
■ Component I/P (Component interlace/
progressive conversion)
Use this feature to activate or deactivate the analog
interlace/progressive conversion of the analog video
signals input at the composite video, S-video and
component video jacks so that the analog video signals
deinterlaced from 480i (NTSC)/576i (PAL) to 480p/576p
are output at the COMPONENT MONITOR OUT jacks.
• This menu item is not available and hence not visible in the GUI
screen if “Conversion” is set to “Off”.
• If your video monitor does not support analog video signals
with 480p/576p of resolution, the GUI screen may not be
displayed on your video monitor when “Component I/P” is set
to “On”. In such a case, set “VIDEO” of “INITIALIZE” in
“ADVANCED SETUP” parameter to “Off” (see page 126).
Manual Setup (Video)
Note
Choice Functions
On Converts composite, S-video, and component
video signals interchangeably and up-converts
composite, S-video, and component video
signals to HDMI video signals.
Off Does not convert any signals.
Notes
Choice Functions
On Activates the analog interlace/progressive up-
conversion of the analog video signals.
Off Deactivates the analog interlace/progressive up-
conversion of the analog video signals.
Notes