Trane INTELLIPAK ™ ™ ™ ™ ™ Commercial Single-Zone Rooftop Air Conditioners with CV or VAV Control - Manual (Page 4)

4
General Information
Model Number Description
All products are identified by a multiple character model
number listed on the unit nameplate. An explanation of the
alphanumeric identification code is provided below. Its use
can define the unit's specific components, type of applica-
tion, i.e. CV or VAV, for a particular unit. When ordering replacement parts or requesting service, be
sure to refer to the specific model number, serial number,
and DL number (if applicable) stamped on the unit name-
plate.
Sam ple Model No.: S X H F - C20 4 0 A 1 0 A 1 5 B 1 D 0 1 A,R,L,etc.
Digit No.: 1 2 3 4 5,6,7 8 9 10 11 12 13 14 15 16 17 18 19 20 21+
Digit 1 - Unit Type Digit 10 - Design Sequence Digit 17 - System Control
S = Self-Contained 3 = Dis connect Redes ign 1 = CV Control (Zone Control)
Note: Sequence may be any letter 2 = VAV-(S/A Temp Control
Digit 2 - Unit Function A thru Z, or an y digit 1 thru 9. without Inlet Guide Vanes)
A = DX Cooling, No Heat 3 = VAV-(S/A Temp Control
E = DX Cooling, Electric Heat Digit 11 - Exhaust Option with Inlet Guide Vanes)
F = DX Cooling, Natural Gas Heat 0 = None 4 = Space Press ure Control with Exhaus t VFD
L = DX Cooling, Hot Water Heat 1 = Barometric without By pass
S = DX Cooling, Steam Heat 2 = 100% - 1.5 HP* 5 = Space Press ure Control with Exhaus t VFD
X = DX Cooling, Extended Cas ings 3 = 100% - 3 HP* and Bypas s
# = DX Cooling, Propane Gas Heat 4 = 100% - 5 HP* 6 = VAV Supply Air Temperature Control
5 = 100% - 7.5 HP* with VFD w/o Bypas s
Digit 3 - Unit Airflow 6 = 100% - 10 HP* 7 = VAV Supply Air Temperature Control
H = Single-Zone 7 = 100% - 15 HP* with VFD and Bypass
8 = 100% - 20 HP* 8 = Supply and Exhaus t Fan with VFD
Digit 4 - Development Sequence A = 50% - 1.5 HP without Bypass
F = Six th B = 50% - 3 HP 9 = Supply and Exhaus t Fan with VFD
C = 50% - 5 HP and By pas s
Digits 5, 6, 7 - Nominal Capacity D = 50% - 7.5 HP
C20 = 20 Tons C55 = 55 Tons E = 100% - 1.5 HP** Digit 18 - Accessory Panel
C25 = 25 Tons C60 = 60 Tons F = 100% - 3 HP** 0 = None
C30 = 30 Tons C70 = 70 Tons G = 100% - 5 HP** A = BAYSENS008*
C40 = 40 Tons C75 = 75 Tons
H = 100% - 7.5 HP** B = BAYSENS010*
C50 = 50 Tons J = 100% - 10 HP** C = BAYSENS013*
K = 100% - 15 HP** D = BAYSENS014*
Digit 8 - Power Supply L = 100% - 20 HP** E = BAYSENS019*
4 = 460/60/3 XL # = 50% w/ Statitrac F = BAYSENS020*
5 = 575/60/3 XL * w/Statitrac G = BAYSENS021*
E = 200/60/3 XL ** w/o Statitrac (CV only )
F = 230/60/3 XL Digit 19 - Ambient Control
Note: SEHF units (unit with Digit 12 - Exhaust Fan Drive 0 = Standard
electric heat) utiliz ing 208V or 0 = None 8 = 800 PRM 1 = 0 Degree Fahrenheit
230V require dual power source. 4 = 400 RPM 9 = 900 RPM
5 = 500 RPM A = 1000 RPM
Digit 20 - Agency Approval
Digit 9 - Heating Capacity 6 = 600 RPM B = 1100 RPM 0 = None (UL Gas Heater, s ee note)
7 = 700 RPM 1 = UL
Note: When the second digit 2 = CSA
calls for "F" (Gas Heat), the Digit 13 - Filter Type Note: Includes UL clsssified gas heating
follow ing values apply: A = Throwaway section only when second digit of
Additionally, please note G and B = Cleanable Wire Mes h Model No. is a "F".
M available ONLY on 50 Ton C = High-Efficienc y Throwaway
models and above. D = Bag with Prefilters Digits 21 - 38 - Miscellaneous
H = High Heat - 2 Stage E = Cartridge with Prefilters 21 A = Unit Disc onnec t Switc h
L = Low Heat - 2 Stage F = No Filters (T/A Rack Only) 22 B = Hot Gas Bypas s
0 = No Heat G = No Filters (Bag/Cart. Rack O nly) 23 C = Economizer Control w/Comparative
J = Limited Modulating High Heat Enthalpy
G = Limited Modulating Low Heat Digit 14 - Supply Fan Horsepower 23 Z = Economizer Control w/Reference
P = Full Modulating High Heat 1 = 3.0 HP 6 = 20.0 HP Enthalpy
M = Full Modulating Low Heat 2 = 5.0 HP 7 = 25.0 HP 23 W = Economiz er Control w/Dry Bulb
Note: When the second digit 3 = 7.5 HP 8 = 30.0 HP 23 O = None W/O Economiz er
calls for "E" (electric heat), the 4 = 10.0 HP 9 = 40.0 HP 1 24 E = Low Leak Fres h Air Dampers
follow ing values apply: 5 = 15.0 HP 25 F = High Duct Temperature Thermos tat
D = 30 KW R = 130 KW 26 G = High Capacity Ev aporator Coil
H = 50 KW U = 150 KW Digit 15 - Supply Fan Drive 27 H = Copper Fins (Cond. only)
L = 70 KW V = 170 KW 5 = 500 RPM B = 1100 RPM 28 K = Generic B.A.S. Module
N = 90 KW W = 190 KW 6 = 600 RPM C = 1200 RPM 29 L = High-Efficiency Motors (Supply & Exhaust)
Q = 110 KW 7 = 700 RPM D = 1300 RPM 30 M = Remote Human Interfac e
Note: When the second digit calls 8 = 800 RPM E = 1400 RPM 31 N = Ventilation Override Module
"L" (Hot Water) or "S" (Steam) 9 = 900 RPM F = 1500 RPM 32 R = Extended Grease Lines
Heat, one of the following valve A = 1000 RPM G = 1600 RPM 33 T = Acc es s Doors
size values must be in Digit 9: 34 V = Interproc ess or Communic ations Bridge
High Heat Coil: 1 = 50", 2 = .75", Digit 16 - Fresh Air Section 35 0 = No c ommunication module
3 = 1", 4 = 1.25", 5 = 1.5", 6 = 2". A = No Fresh Air 35 Y = Trane Communic ation Interfac e Module
Low Heat Coil: A = .50", B = .75", B = 0-25% Manual 35 7 = LonTalk® Communication Interface Module
C = 1", D = 1.25", E = 1.5", F = 2". D = 0-100% Ec onomizer 36 8 = Spring Is olators
37 6 = Factory-Powered 15A G FI Conv enienc e
O utlet
38 0 = None
1. Available as standard 460 volt only for 70 and 75 ton models.