Onkyo TX-DS989 - Manual (Page 42)

42
Listening Mode Setup
3. Listening Mode Setup menu
This menu allows you to make fine adjustments to the listening
modes you have set for each input source with the Listening Mode
Preset sub-menu. These adjustments are in the form of parameters
and each one is explained below. Note that some parameters
cannot be set for some listening modes and that no sub-menu will
have all parameters. Also, for some input signal formats, changes
in the listening mode parameters may actually result in no change
to the resulting output signal.
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3.Listening Mode Setup
1.Mono(Analog/PCM)
2.Mono(Digital)
3.Stereo(Analog/PCM)
4.Stereo(Digital)
5.Surround(Analog/PCM)
6.Surround(Digital)
7.Theater-Dimensional
Quit:|OSD|
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3.Listening Mode Setup
1.Mono(Analog/PCM)
2.Mono(Digital)
3.Stereo(Analog/PCM)
4.Stereo(Digital)
5.Surround(Analog/PCM)
6.Surround(Digital)
7.Theater-Dimensional
Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3-1.Mono(Analog/PCM)
a.Subwoofer :On
b.Re-EQ/Academy
:Re-EQ
c.Input Channel
:AutoL+R
d.Output Channel
:L+R
Quit:|OSD|
Currently
selected
listening mode
3-1. Mono (Analog/PCM) Setup
Select this to modify the Mono listening mode when the current
source is analog or PCM. The parameters that can be set are shown
in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Input Channel Auto L+R, Left, Right Auto L+R
d Output Channel L+R, Center L+R
3-2. Mono (Digital) Setup
Select this to modify the Mono listening mode when the current
source is digital. The parameters that can be set are shown in the
table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Input Channel Auto L+R, Left, Right Auto L+R
d Output Channel L+R, Center L+R
3-3. Stereo (Analog/PCM) Setup
Select this to modify the Stereo listening mode when the current
source is analog or PCM. The parameters that can be set are shown
in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Digital Upsampling Off, On Off
The c. Digital Upsampling can only be set for PCM input sources
and cannot be set for analog ones.
3-4. Stereo (Digital) Setup
Select this to modify the Stereo listening mode when the current
source is digital. The parameters that can be set are shown in the
table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
3-5. Surround (Analog/PCM) Setup
Select this to modify the Pro Logic Surround listening mode when
the current source is analog or PCM. The parameters that can be
set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ On, Off Off
c Surround Speakers Surround L/R, Surround Back, Surround L/R
Surround L/R+Back
d Digital Upsampling Off, On Off
The d. Digital Upsampling can only be set for PCM input sources.
Furthermore, if this is set to On, c. Surround Speaker is fixed to
“Surround L/R.”