Using the remote control – RCA Scenium D61W136DB User Manual
Page 19
16
Chapter 2
Using the Remote Control
Graphics contained within this publication are for representation only.
Chapter 2
17
Using the Remote Control
Graphics contained within this publication are for representation only.
Note:
The DVD, VCR, SAT/CAB, AUX/HD, and
AUDIO buttons also turn on most RCA, GE,
and Proscan products.
INFO In TV mode, makes the channel banner appear and disappear. In DVD
mode, makes the info banner appear and disappear.
INPUT Accesses the available video input channels (VID1, VID2, FRNT, CMP1,
CMP2 and DVI). Press the CH+ or CH- button to resume TV viewing.
LIGHT Press to illuminate the remote control’s buttons (except for the component
buttons). To conserve battery power, the light turns off after several seconds.
Backlight won’t activate if batteries are low, but blinks on and off quickly.
MENU In TV mode, makes the TV Main menu appear and disappear. In DVD
mode, makes the reduced TV menu appear and disappear.
MUTE Reduces the TV’s volume to its minimum level. Press again to restore the
volume.
OK When in the menu system, selects highlighted items. When watching TV,
freezes the picture until you press any button on the remote to resume normal TV
viewing. Please note that when you "unfreeze" you go back to live programming
(skipping any programming that occurred during the freeze).
ON•OFF When in TV mode, turns the TV on and off. If in another component
mode (VCR, DVD, SAT/CAB, AUX/HD or AUDIO) and programmed, turns the
component on and off.
PIP Press once to bring up the small picture-in-picture (PIP) window. Press again
to bring up the picture-outside-picture (POP) windows. Press to remove POP. (See
Chapter 4 for more information about using PIP.)
PIP + or PIP – When using PIP or POP, changes the channel in the PIP window.
PRESETS In TV mode, displays the Picture and Sound preset settings. Use the up
and down arrow buttons to highlight either Picture or Sound settings. Use the left
and right arrow buttons to change to a different Picture or Sound preset. In DVD
mode while a disc is playing, displays the DVD Info Display with the Audio icon
highlighted.
REC If programmed, starts recording TV programs if your TV/DVD is connected
to a recording device (such as a VCR) if the remote is in the right mode to control
that device.
REV, PLAY, FWD, STOP, PAUSE In DVD mode, these buttons provide reverse, play,
fast forward, stop and pause the disc. If programmed, they also provide transport
control for some remote-controllable VCRs, DVD players, tape decks, and CD players.
SAT/CAB Puts the remote in SAT/CAB mode and, if Autotuning is enabled, turns
on the TV and tunes to the correct input channel.
SKIP In TV mode, press once before changing channels and the TV will wait 30
seconds before returning you to the original channel. Press repeatedly to add more
time.
SLEEP Brings up the Sleep timer menu. Use the right and left arrow buttons
on the remote control to increase or decrease the sleep timer in five minutes
increments (up to a maximum of four hours).
SWAP When using PIP, swaps the main picture with the PIP window. When using
POP, swaps the left and right pictures.
TV Turns on the TV and puts the remote in TV mode. Also displays the channel
banner.
VCR Puts the remote in VCR mode and, if Autotuning is enabled, turns on the TV
and tunes to the correct input channel.
VOL – or VOL + Decreases or increases the TV’s volume.
ZOOM In PIP mode, changes the size of the PIP window.
Tip
The component button corresponding
to the mode you're in flickers when the
remote batteries are low and you press a
button on the remote.
A warning message may also appear on
the screen when you press a remote button
and the batteries are low.
Tip
To turn off most RCA, GE, and Proscan
components that are connected to the TV,
press ON•OFF twice within two seconds.
This feature only works with most RCA, GE,
and Proscan products.