Roland XV-5080. - Manual (Page 289)

289
MIDI Implementation
Appendices
❍ Panpot (Controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Panpot:
00H - 40H - 7FH (Left - Center - Right),
Initial value = 40H (Center)
❍ Portamento (Controller number 65)
Status 2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
❍ Resonance (Controller number 71)
Status 2nd byte 3rd byte
BnH 47H vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv= Resonance value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Release Time (Controller number 72)
Status 2nd byte 3rd byte
BnH 48H vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Release Time value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Attack time (Controller number 73)
Status 2nd byte 3rd byte
BnH 49H vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Attack time value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Cutoff (Controller number 74)
Status 2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Cutoff value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Decay Time (Controller number 75)
Status 2nd byte 3rd byte
BnH 4BH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Decay Time value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Vibrato Rate (Controller number 76)
Status 2nd byte 3rd byte
BnH 4CH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Vibrato Rate value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Vibrato Depth (Controller number 77)
Status 2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Vibrato Delay (Controller number 78)
Status 2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)
❍ Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Reverb Send Level:00H - 7FH (0 - 127)
❍ Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte 3rd byte
BnH 5DH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Chorus Send Level:00H - 7FH (0 - 127)
❍ RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n = MIDI channel number:0H - FH (Ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB Notes
00H, 00H mmH, llH Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
* In Performance mode, the Part Pitch Bend Range parameter
(PERFORM/PART) will change.
00H, 01H mmH, llH Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H (-8192*50/8192 - 0 -
+8192 *50/8192 cent)
* In Performance mode, the Part Fine Tune parameter (PERFORM/
PART) will change.
00H, 02H mmH, llH Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* In Performance mode, the Part Coarse Tune parameter (PERFORM/
PART) will change.
7FH, 7FH ---, --- RPN null
RPN and NRPN will be set as "unspecified". Once this setting has been
made, subsequent
Parameter values that were previously set will not change.
mm, ll: ignored
● Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:0H - FH (Ch.1 - 16)
pp = Program number:00H - 7FH (prog.1 - prog.128)
■ System Exclusive messages
Universal Non-realtime System Exclusive Message" and Data Set 1 (DT1) are the only
System Exclusive messages transmitted by the XV-5080.
● Universal Non-realtime System Exclusive Message
❍ Identity Reply Message
Receiving Identity Request Message, the XV-5080 send this message.
Status Data byte Status
F0H 7EH, dev, 06H, 02H, 41H, 10H, 01H, 00H, F7H
00H, 00H, 00H, 00H, 00H
Byte Explanation
FOH Exclusive status
7EH ID number (Universal Non-realtime Message)
dev Device ID (use the same as the device ID of Roland)
06H Sub ID#1 (General Information)
02H Sub ID#2 (Identity Reply)
41H ID number (Roland)
10H 01H Device family code
00H 00H Device family number code
00H 00H 00H 00H Software revision level
F7H EOX (End of Exclusive)