NAD S170iAV - Manual (Page 11)

ENGLISH
FRANÇAIS
DEUTSCH
ESP
AÑOL
IT
ALIANO
POR
TUGUÊS
SVENSKA
11
REAR PANEL
ATTENTION!
Please make all connections to your S170i preamplifier with the unit
powered off or unplugged. (It is equally wise to power-down or
unplug all associated components while making or breaking any
signal or AC power connections.)
1 COMPOSITE VIDEO IN 1-6: Connect Video Inputs 1-6 to composite
video from source components (see “Source Setup,” below).
2 COMPOSITE VIDEO OUT 4-6 OUT; MON OUT: Connect to
composite-video record-inputs of recording components; connect
MON OUT to the composite-video input of the video monitor/TV.
3 S VID1 IN - S VID6 IN: Connect Video Inputs 1-6 to S-Video from
source components (see “Source Setup,” below).
4 S VID4 OUT - SVID6 OUT; MON OUT: Connect to S-Video record
inputs of recording components; connect MON OUT to the S-Video
input of the video monitor/TV.
5 COMPONENT VIDEO IN (upper), OUT (lower): Connect inputs to
component-video signal or wide-band component video from a
source component such as a DVD player or HDTV tuner; connect
outputs to the component-video inputs of the video monitor/TV. Be
sure to observe consistency in connecting the Y, CB, and CR jacks to
the corresponding sources/inputs (see “Source Setup,” below).
6 NAD LINK IN/OUT: Connect to the corresponding NAD Link jacks
(input to output and vice versa) of compatible NAD components (see
“NAD Link,” below).
7 DIGITAL 1-3; DIGITAL IN; DIGITAL OUT: Connect DIGITAL 1-3 to
coaxial S/PDIF-format digital sources such as CD or DVD players;
connect DIGITAL IN to a high-quality S/PDIF-format source via BNC
cabling; connect DIGITAL OUT to the coaxial S/PDIF digital input of a
recording component such as a CD recorder, DAT deck, or computer
soundcard (see “Source Setup,” below).
8 OPTICAL DIGITAL IN 1-2; DIGITAL IN; OPTICAL DIGITAL OUT:
Connect OPTICAL DIGITAL 1-2 to optical S/PDIF-format digital
sources such as CD or DVD players; connect OPTICAL DIGITAL OUT
to the optical S/PDIF digital input of a recording component such as
a CD recorder, DAT deck, or computer soundcard.
9 RS-232: Connect to the RS-232 serial port of a home-automation
system or personal computer (see “System Integration,” below).
10 VIDEO 1-6 Analog Audio Inputs: Connect to stereo analog
outputs of audio-video sources (see “Source Setup,” below).
11 VIDEO ANALOG REC OUT 4-6: Connect to stereo analog inputs of
recording audio-video components such as videocassette recorders.
12 CD, AUX, TUNER Inputs: Connect to stereo analog outputs of
audio components.
13 TAPE MONITOR IN/OUT: Connect OUT to the stereo analog inputs,
and IN to the outputs of an audio recording components such as a
cassette deck or CD recorder, or of an analog audio processor such
as a stereo equalizer.
14 MULTISOURCE OUT: Connect to the inputs of the stereo amplifier
(integrated amp, receiver) that will power the remote-zone’s
loudspeakers (see “Listening in a Remote Zone,” below).
15 PREAMP ANALOG 7.1 OUTPUTS: Connect L, R, and CENTER to
the channel inputs of the power amplifier(s) driving the front,
channels; connect LS and RS to the power amplifier driving the
surround speakers and LEFT B and RIGHT B to that driving the
surround-back speakers (if any); connect sub to the line input of a
powered subwoofer or to the amplifier driving a passive sub (if any).
16 EXTERNAL 5.1 INPUTS: Connect to the corresponding analog
audio outputs of a multichannel source component such as a DVD-
Audio or multichannel SACD player. There is no bass-management
or other processing available to these inputs; see “Selecting
Sources,” below.
17 12V TRIGGERS: Connect to the 12-volt trigger inputs of compatible
components such as power amplifiers and projector lifts; see “Trigger
setup,” below.
18 AC power inlet: Connect to the supplied IEC-standard removable
AC power cord or a compatible cord.