Nokia 5140 - Manual (Page 55)

You can find the declination values in special maps or lists of locations. Note that the declination value is dependent on both
the location and time. Therefore, you should periodically check the correct value from up to date sources and always set the
declination according to your location when using the compass. For more information on declination, see www.nokia.com/
phones/5140/compass.
While using the compass, hold the phone horizontally by using the bubble level in the top left corner of the phone. The
compass deactivates and goes into standby mode after a certain time to save power; press
Continue to activate the
compass again. You can prevent the compass from going into standby mode by pressing a number key every few minutes.
You can use the flashlight when the compass is active.
Calibrating the compass
1. Press Menu , and select Applications → Extras → Compass .
2. If the phone requests you to calibrate the compass, Compass must be calibrated first is shown. Otherwise, press Options ,
and select Calibration . If the direction of the intended destination has been set, press Reset to reset the direction.
3. To start the calibration, press Yes . Place the phone on a horizontal, level surface, and carefully rotate it; or, while holding
it horizontally, slowly turn it around. Use the rotating graphic on the display to observe the speed of rotation. When the
calibration is finished,
Compass calibrated appears.
Setting the declination
1. Press Menu , and select Applications → Extras → Compass .
2. Press Options , and select Settings → Declination → Set declination to set the declination.
To activate the last set declination value, select On .
3. Key in the declination value in degrees from 0 to 180, and press OK .
4. Select the direction of the declination: East (+) or West (-). Declination on appears.
Setting and resetting the direction
1. Press Menu , and select Applications → Extras → Compass .
The current direction in which the phone is being held appears in degrees (from north) at the top left of the display. If the
direction of the intended destination has been set, it appears at the top right of the display.
2. To reset the direction of the intended destination, press Reset and Yes . Point the phone in the direction of the intended
destination, and press Set direc. .
3. The arrow points in the direction you have set, and the numeric value is shown at the top right of the display. When the
arrow points up on the display, the phone is pointed in the correct direction. The arrow rotates according to the
movement of the phone.
To stay in the set direction, the arrow should point up on the phone display.
Countdown timer
To start the countdown timer, press Menu , select Applications → Extras → Countdown timer , and press Select . Key in the
alarm time, and press OK . If you want, write your own note that is displayed when the time expires.
To change the countdown timer, select Change time ; or to stop the timer, select Stop timer .
If the set alarm time is reached when the phone is in standby mode, the phone sounds a tone and flashes the note you
created or
Countdown time up . To mute the alarm, press any key. If no key is pressed, the alarm stops within 30 seconds. To
stop the alarm and delete the text note, press Exit . To set the countdown timer again, press Restart .
Stopwatch
Using the stopwatch or allowing it to run in the background when using other features increases the demand on battery
power and reduces the battery life.
During timing, the other functions of the phone can be used. To set the stopwatch timing in the background, press .
Measuring intermediate times
1. Press Menu , and select Applications → Extras → Stopwatch → Split timing . To view the timing that you have set in the
background, press Continue .
2. To start the time observation, press Start . Press Split each time that you want to take an intermediate time. The
intermediate times are listed below the elapsed time on the display.
3. To stop measuring time, press Stop .
4. To save the time, press Save . Key in a name for the measured time, and press OK . If no name is keyed in, the total time is
used as the title.
5. To start measuring time again, press Options , and select Start . The new time is added to the previous time. To reset the
time without saving it, select Reset .
A p p l i c a t i o n s
Copyright © 2004 Nokia. All Rights Reserved. 55