Pioneer PRO-950HD - Manual (Page 8)

8
En
Important User Guidance Information 01
Caution
Pioneer bears no responsibility for any damage arising from
incorrect use of the product by you or other people, malfunctions
when in use, other product related problems, and use of the
product except in cases where the company must be liable.
Plasma display protection function
When still images (such as photos and computer images) stay on
the screen for an extended period of time, the screen will be
slightly dimmed. This is because the protection function of the
plasma display automatically adjusts the brightness to protect
the screen when detecting still images; so this does not
designate malfunction. The screen is dimmed when a still image
is detected for about three minutes.
Information of pixel defect
Plasma screens display information using pixels. Pioneer plasma
display panels contain a very large number of pixels. (Depending
on the panel size; over 2.3 million pixels in case of a 42 inch
display, over 3.1 million pixels in case of a 50 inch display). All
Pioneer display panels are manufactured using a very high level
of ultra-precision technology and undergo individual quality
control.
In rare cases, some pixels can be permanently switched off, or
on, resulting in either a black or colored pixel permanently fixed
on the screen.
This effect is common to all plasma displays because it is a
consequence of the technology.
If the defective pixels are visible at a normal viewing distance of
between 2.5 and 3.5 meters (8.2 and 11.5 feet) while viewing a
normal broadcast (i.e. not a test card, still image or single color
display) please contact Pioneer Customer Support Div. (USA) or
Customer Satisfaction Dept. (CANADA). See back cover.
If, however, they can only be seen close up or during single color
displays then this is considered normal for this technology.
Infrared rays
The plasma display releases infrared rays because of its
characteristics. Depending on how the plasma display is in use,
the remote controls of nearby equipment may be adversely
affected or wireless headphones using infrared rays are
interfered with by noise. If this is the case, place that equipment
at a location where its remote control sensor is not affected.
Radio interference
While this product meets the required specifications, it emits a
small amount of noise. If you place such equipment as an AM
radio, personal computer, and VCR close to this product, that
equipment may be interfered. If this happens, place that
equipment far enough from this product.
Plasma display driving sound
The screen of the plasma display is composed of extremely fine
pixels and these pixels emit light according to received video
signals. This principle may cause you to hear a buzz or electrical
hum coming from the plasma display.
Do not attach such items as labels and tape to the
product.
• This may result in the discoloration or scratch of the cabinet.
When not using the product for a long period of time
• If you do not use the product for a long period of time, the
functions of the product may be adversely affected. Switch on
and run the product occasionally.
Condensation
• Condensation may take place on the surface or inside of the
product when the product is rapidly moved from a cold place
to a warm place or just after a heater is switched on on a winter
morning, for example. When condensation takes place, do not
switch on the product until condensation disappears. Using
the product with condensation may result in malfunction.
Cleaning the surface of the screen and the glossy
surface of the front cabinet
• When cleaning the surface of the screen or the glossy surface
of the front cabinet, gently wipe it with a dry soft cloth; the
supplied cleaning cloth or other similar cloths (e.g., cotton and
flannel). If you use a dusty or hard cloth or if you rub the screen
hard, the surface of the product will be scratched.
• If you clean the surface of the screen with a wet cloth, water
droplets on the surface may enter into the product, resulting in
malfunction.
Cleaning the cabinet
• When cleaning the cabinet of this product, gently wipe it with
a clean soft cloth (e.g., cotton and flannel). If you use a dusty or
hard cloth or if you rub the cabinet hard, the surface of the
cabinet will be scratched.
• The cabinet of this product is mostly composed of plastic. Do
not use chemicals such as benzene or thinner to clean the
cabinet. Using these chemicals may result in quality
deterioration or coating removal.
• Do not expose the product to volatile gas or fluid such as
pesticide. Do not bring the product in contact with rubber or
vinyl products for a long period of time. The effect of plasticizer
in the plastic may result in quality deterioration or coating
removal.
• If you clean the surface of the cabinet with a wet cloth, water
droplets on the surface may enter into the product, resulting in
malfunction.
Handles at the rear of the plasma display
• Do not remove the handles from the rear of the plasma display.
• When moving the plasma display, ask another person for help
and use the handles attached to the rear of the plasma display.
Do not move the plasma display by holding only a single
handle. Use the handles as shown on page 16.
• Do not use the handles to hang the product when installing or
carrying the product, for example. Do not use the handles for
the purpose of preventing the product from tilting over.
PRO1150HD.book Page 8 Tuesday, April 17, 2007 9:34 AM