09 tuner setup, Setting up tv channels, Tuner setup – Pioneer PRO-950HD User Manual
Page 36: Tuner setup 09, Chapter 9
36
En
Tuner Setup
09
Chapter 9
Tuner Setup
Setting up TV channels
This section describes how to search and set up TV channels that
you can watch under the current conditions. Unless you set up
TV channels using Auto Channel Preset, you may not be able to
tune in those channels.
Using Auto Channel Preset
Auto Channel Preset automatically searches and sets up TV
channels.
1
Press HOME MENU.
2
Select “Tuner Setup” ( / then ENTER).
3
Select “Channel Setup” ( / then ENTER).
4
Select “Ant. A” or “Ant. B” ( / then ENTER).
5
Select “Auto Channel Preset” ( / then ENTER).
6
Select “Air” or “Cable” ( / then ENTER).
• Channel search automatically starts.
• To quit Auto Channel Preset halfway, press
D.
7
After Auto Channel Preset has been finished, press
HOME MENU to exit the menu.
Note
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.
• When an inserted CableCARD™ is functioning, you can
execute Auto Channel Preset by selecting “Ant.B” in step 4.
Setting for skipping unwanted channels
From among TV channels searched and set up using Auto
Channel Preset, you can select channels to be skipped when
CH+/- are operated.
1
Press HOME MENU.
2
Select “Tuner Setup” ( / then ENTER).
3
Select “Channel Setup” ( / then ENTER).
4
Select “Ant. A” or “Ant. B” ( / then ENTER).
5
Select “Channel Keep/Skip” ( / then ENTER).
6
Select a channel to be skipped ( / then ENTER).
• For the skipped channel, a check mark disappears.
7
Press HOME MENU to exit the menu.
Note
• To restore skipped channels, use the above procedure except
that you select a skipped channel in step 6.
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.
Setting up TV channels manually
This section describes how to manually set up TV channels that
have not been set up by Auto Channel Preset.
1
Press HOME MENU.
2
Select “Tuner Setup” ( / then ENTER).
3
Select “Channel Setup” ( / then ENTER).
4
Select “Ant. A” or “Ant. B” ( / then ENTER).
5
Select “Add Channel” ( / then ENTER).
6
Select a channel number to be added ( / then ENTER).
• You can also use buttons
0 to 9 to enter a channel number.
• After
ENTER has been pressed, a confirmation screen
appears.
7
Press A to complete the setup process.
8
Press HOME MENU to exit the menu.
Note
• Adding channels manually is for adding analog channels only.
Digital channels cannot be added.
Checking signal strength
When you have selected antenna A, you can check the current
channel’s signal strength. You may use this function when
receiving a channel through a VHF/UHF antenna.
1
Press HOME MENU.
2
Select “Tuner Setup” ( / then ENTER).
3
Select “Channel Setup” ( / then ENTER).
4
Select “Ant. A” ( / then ENTER).
Channel Setup
Begin Preset
Cancel
Exit
Ant. A
Auto Ch. Preset
Cable
Air
Cable
Ant. A
Auto Channel Preset
2.0
4.0
6.0
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Enter
Home Menu
D
Channel Setup
Cancel
Exit
Ant. A
Auto Ch. Preset
Cable
Ant. A
Auto Channel Preset
• Cable
One Moment Please …
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
Home Menu
D
Channel Setup Ant. A
Channel Keep/Skip
Ant. A
Channel Keep/Skip
2.0
4.0
6.0
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Exit
Home Menu
Channel Setup Ant. A
Add Channel
000
Ant. A
Add Channel
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
1
Exit
Home Menu
PRO1150HD.book Page 36 Tuesday, April 17, 2007 9:34 AM