Pioneer Elite VSX-23TXH - Manual (Page 71)

Using other functions 08
71
En
Using the sleep timer
The sleep timer switches the receiver into standby after a
specified amount of time so you can fall asleep without
worrying about the receiver being left on all night. Use
the remote control to set the sleep timer.
• Press , then press SLEEP repeatedly to set
the sleep time.
• You can check the remaining sleep time at any time
by pressing SLEEP once. Pressing repeatedly will
cycle through the sleep options again.
1
Dimming the display
You can choose between four brightness levels for the
front panel display. Note that when selecting sources, the
display automatically brightens for a few seconds.
• Press , then press DIMMER repeatedly to
change the brightness of the front panel display.
Switching the HDMI output
(VSX-23TXH only)
Set which terminal to use when outputting video and
audio signals from the HDMI output terminals (HDMI
OUT ALL, HDMI OUT 1 or HDMI OUT 2).
The HDMI OUT1 terminal is compatible with the KURO
LINK function.
• Press , then press HDMI OUT.
Please wait a while when Please wait ... is displayed.
The output switches among HDMI OUT ALL, HDMI OUT 1
and HDMI OUT 2 each time the button is pressed.
2
Checking your system settings
Use the status display screen to check your current
settings for features such as surround back channel
processing and your current MCACC preset.
1 Press , then press STATUS to check the
system settings.
These appear on the front panel display.
3
The front panel display shows each of the following
settings for three seconds each:
2 When you’re finished, press STATUS again to
switch off the display.
Note
1 • You can also switch off the sleep timer simply by switching off the receiver.
• The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.
1 2 3
SLEEP
HDMI OUT
MCACC SIGNAL SEL
4 5 6
DIMMER A.ATT SBch
7 8 9
CLASS CH LEVEL D.ACCESS
0 ENTER
INPUT
SELECT
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO INFO
DISP
CH
RECEIVER TV CTRL
RECEIVER
30 min 60 min
90 min Off
1 2 3
SLEEP
HDMI OUT
MCACC SIGNAL SEL
4 5 6
DIMMER A.ATT SBch
7 8 9
CLASS CH LEVEL D.ACCESS
0 ENTER
INPUT
SELECT
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO INFO
DISP
CH
RECEIVER TV CTRL
RECEIVER
2 • Synchronized amp mode on page 65 is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch
to HDMI OUT 1, then select the synchronized amp mode on the flat panel TV using the flat panel TV’s remote control.
• When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3 (VSX-
21TXH)/4 (VSX-23TXH), or BD.
3 If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.
Input Source
↓
Sampling Frequency
↓
Surround Back channel Processing
↓
MCACC preset
↓
ZONE 2 input
↓
ZONE 3 input
(VSX-23TXH only)
↓
KURO LINK
↓
HDMI OUT
(VSX-23TXH only)
1 2 3
SLEEP
HDMI OUT
MCACC SIGNAL SEL
4 5 6
DIMMER A.ATT SBch
7 8 9
CLASS CH LEVEL D.ACCESS
0 ENTER
INPUT
SELECT
REMOTE
SETUP
ZONE 2
MAIN
ZONE 3
AUDIO INFO
DISP
CH
RECEIVER TV CTRL
RECEIVER
PHASE CTRL THX STATUS
REMOTE
SETUP
ANT MEMORY
AUDIO INFO
DISP
MPX PQLS
CH
RECEIVER TV CTRL
RECEIVER
VSX-23TXH_CUXJ.book 71 ページ ２００９年５月８日 金曜日 午前１０時４５分