Realignment, Self programming mode (tk-270g only) – Kenwood TK-270G User Manual
Page 11

TK-260G/270G
11
8-2. Channel Setting Mode
This is a mode for making channel settings with the panel
keys without using the FPU.
Pressing [MON] when "SELF" is displayed, sets Channel
Setting Mode.
Select an item set using [
3
] then change the selection with
the encoder.
The data displayed using [
2
] is stored in the memory and
then proceeds to the next item. Pressing [
3
] proceeds to
the next item without storing it in the memory.
Press [MON] to set the display to "SELF" and return to reset
(default) status.
Fig. 3
REALIGNMENT
8. Self Programming Mode (TK-270G only)
Write mode for frequency data and signalling etc. Mainly
used by the person maintaining the user equipment.
8.1 Self programming mode setting
Remove D17 from the TX-RX unit (Figure 3) (K models
only). Hold down the [LAMP]+[
●
] switches and turn the
power switch on.
When the self programming mode is entered, [SELF]
appears on the display. The mode changes automatically
to Model Select Mode and "PORTABLE" is displayed in
about one second.
Note :
This mode (self programming mode) cannot be set when it
has been disabled with the FPU.
No. Function
Choices
Display
Remarks
Select
1-128
_1-_1._
[
3
] : Group selection/
Channel
_1-128._
Channel selection change
Select
1-128
_1.-_1_
Group
128.-_1_
1
RX frequency Step 2.5kHz-1MHz
STP_250
Display when an item is selected
STP_1000 or when a step is changed
(about 0.5 seconds)
[
•
] Step change
VHF : 2.5, 5.0,6.25,7.5kHz,1MHz,Step
Blank
————
[LAMP] : Freq On/Blank switching
100.0000-
R.100.0000 The rightmost dot indicates
550.0000MHz
50Hz digit (On=5; Off=0).
2
Rx Signaling OFF
————
[LAMP] : Off/QT/DQT switching
QT 67.0-250.3Hz
QT_67.0_ [
•
] : Mode switching
(EIA Mode)
QT_250.3_ [
°
] : Normal/Inverse
QT 67.0-250.3Hz
QT_67.0*
switching
(0.1Hz Step Mode)
QT_250.3*
DQT 000-777 (Normal) DQT000N*
(1 Step Mode)
DQT777N*
DQT 023-754 (Normal) DQT023N
(Standard Table Mode) DQT754N
DQT 000-777 (Inverse) DQT000I*
(1 Step Mode)
DQT777I*
DQT 023-754 (Inverse) DQT023I
(Standard Table Mode) DQT754I
D17
X57-587X
Compoent Side
Radio type
Portable
Mobile
[MON]
Radio Band & Channel Type
Function set mode
Frequency Version
Self programming mode
[
2]
[
2]
[LAMP]
VHF 8CH
Channel set mode
[
2]
[
3]
VHF 128CH
UHF 8CH
UHF 128CH
[CH]
[CH]
[CH]
[CH]
[CH]
VHF F1
VHF F2
UHF F1
UHF F3
[CH]
[CH]
[CH]
UHF F4
[CH]
[CH]
Cannot be
set when
Portable is
select
Cannot be
set when
Mobile is
select
●
Flow Chart
Note :
IF the radio type of TK-270G was temporally set to "Mobile"
for the cloning purposes, "UNPROG" is displayed (at User
Mode) when the TK-270G is turned on.
In this case, please set the radio type back to "Portable" at
Model Select Mode menu.