Kenwood KRF-X9090D - Manual (Page 38)

38 EN
Ambience effects
= DTS 96/24+THX MusicMode : DTS 96/24 +THX MusicMode*3
~ DTS+THX Select2 Cinema : DTS+THX Select2 Cinema*4
! DTS 96/24+THX Select2 Cinema : DTS 96/24+THX Select2
Cinema*4
@ DTS-ES Mtrx 6.1 : DTS-ES Matrix 6.1*5
# DTS-ES Dscrt 6.1 : DTS-ES Discrete 6.1*5
$ DTS : DTS*5
% DTS+Neo:6 Cin : DTS+Neo:6 Cinema*5
^ Neo:6 Cinema : Neo:6 Cinema*5
& Neo:6 Music : Neo:6 Music*5
* DTS 96/24 : DTS 96/24*5
( Stereo : Stereo*5
When the analog signal or the digital signal (except for
Dolby Digital or DTS signal) is input :
1 PLII Movie+THX Cinema : Dolby Pro Logic II Movie mode
+THX Cinema*1
2 Pro Logic+THX Cinema : Dolby Pro Logic+THX Cinema*1
3 Neo:6 Cinema+THX Cinema : Neo:6 Cinema+THX Cinema*1
4 Stereo+THX Cinema
: Stereo+THX Cinema*1
5 2.0 THX Games : 2.0 THX Games*2
6 PLIIx Movie : Dolby Pro Logic IIx Movie mode*5
7 PLIIx Music : Dolby Pro Logic IIx Music mode*5
8 PLIIx Game : Dolby Pro Logic IIx Game mode*5
9 PLII Movie : Dolby Pro Logic II Movie mode*5
0 PLII Music : Dolby Pro Logic II Music mode*5
- PLII Game : Dolby Pro Logic II Game mode*5
= Pro Logic : Dolby Pro Logic*5
~ Neo:6 Cinema : Neo:6 Cinema*5
! Neo:6 Music : Neo:6 Music*5
@ Stereo : Stereo*5
• *1 THX Cinema mode only.
*2 THX Games mode only.
*3 THX MusicMode only.
*4 THX Select2 Cin only.
*5 THX OFF only.
• Dolby Digital or DTS signal having more channels than the maximum
number of playback channels available using the receiver’s current
settings is input, downmixing is performed to match the number of
available channels.
4
Adjust the volume.
DSP mode
This mode can be selected when digital signals other than Dolby
Digital or DTS, or analog signal come in.
This mode can be selected when THX mode is off.
1 Pressing the DSP key or DSP MODE key will display the
current DSP MODE status.
2 Each press of the key will switch to the next status as shown
bellow:
1 Arena : Arena mode.
2 Jazz Club : Jazz Club mode.
3 Theater : Theater mode.
4 Stadium : Stadium mode.
5 Disco : Disco mode.
• The DSP mode selection is displayed for approximately 3 seconds.
Switching the LISTEN mode to Stereo temporarily
Pressing the STEREO key changes the currently selected LISTEN mode
into Stereo. It will be changed back to the original LISTEN mode by
pressing the STEREO key again.
• If the power is turned off and turned back on, or the input selector is
switched to another and switched back, the LISTEN mode will be back to
the original one.
Notes
• Depending on the type of the signal or speaker setting, some listening
modes cannot be selected.
• When playback is started, the sound may be cut or interrupted before
the input source is confirmed as Dolby Digital or DTS.
• To enjoy Dolby Digital surround (as well as all the other listening modes)
from a single component, be sure to use a Dolby Digital compatible
source component.
• Dialogue Normalization (Dial Norm) is a feature of Dolby Digital. It is able
to automatically maintain the overall audio output level constant.
L
SL SR
C R
SP MUTE
A B CLIP
LFE
DIGITAL DOLBY DIGITAL EX
DOLBY PL II x
STEREO AUTO DETECT
When playing some Dolby Digital sources, you may see in the display
a message "DIALNORM OFFSET xxdB". This is because some
soundtracks may be recorded either louder or quieter than normal. The
xx number shows by how much.
For example, if the message says “DIALNORM OFFSET +4dB” you
know that this particular recording was encoded 4dB louder than
normal. If you wish, you can turn down the volume control by 4dB to
keep the playback level consistent.
05.7.18, 2:34 PM 38