Sharp MD-X60H - Manual (Page 54)

YO
(Continued)
When an error message is displayed, proceed as follows:
Error messages Meaning Remedy
BLANK MD ● Nothing is recorded. ● Replace it with another disc.
Can’t COPY ● You tried to record from a copy-protected disc. ● Replace it with a regular disc that can be copied.
Can’t EDIT ● A track cannot be edited. ● Change the stop position of the track and then try editing
it.
Can’t REC ● Recording cannot be performed correctly due to vibra-
tion or shock in the unit. ● Re-record.
Can’t T REC ● Timer recording is impossible or there is no available
space on the MD. ● Replace it with another disc.
CH ERROR ● There is something wrong with the CD changer. ● Set this unit to the stand-by mode and then back to on,
and press the
0 6 button.
CONNECT ERR ● Whilst an MD player is being edited on this unit, incorrect
digital signals are input from the portable MD player. ● Make sure the cable is connected correctly and that
power is being supplied to the portable MD player.
DEFECT ● Since this disc has scratches on it, the recording oper-
ation was skipped. ● Replace it with another disc.
Din UNLOCK ● Incorrect digital signals are input. ● Connect correct digital signals.
● Use the analogue input sockets.
DISC ERR ● The disc is damaged.
● A TOC is not written on the MD or there is something
wrong with data.
● Reload the disc or replace it.
DISC FULL ● The disc is out of recording space. ● Replace the disc with another recordable disc.
EDIT OVER ● There is no space to make CD editing on the disc. ● Replace it with a disc that has enough time to record.
FOCUS ERROR ● A disc has not been loaded.
● The disc data cannot be read.
● Reload the MiniDisc.
MD ERROR ● No operation. ● Contact the shop where you purchased the unit.
MECHA ERR ∗
( ∗ :N um ber or
symbol)
● There is a mechanical problem and the disc is not work-
ing properly. ● Set this unit to the stand-by mode and press the 7 but-
ton.
NAME FULL ● The number of characters for the disc name or track
name exceeds 100. ● Shorten the disc or track name.
NO DISC ● A disc has not been loaded.
● The disc data cannot be read.
● Load a disc.
● Reload the disc.
NOT AUDIO ● The data recorded on this disc is not audio data. ● Select another track.
● Replace the disc.
PLAYBACK MD ● You tried to record on a playback-only disc. ● Replace it with another recordable disc.
PROTECT ● Trouble is found. ● Restart the unit. If the unit doesn’t work, contact a
SHARP Authorised Servicing Dealer or SHARP Auth-
orised Service station.
PROTECTED ● The disc is write protected.
● The tape is protected against accidental erasure.
● Move the write protection tab back to its original position.
● Cover the accidental erase prevention hole.
TAPE ERROR ● The tape mechanism is defective. ● Try pressing the RESET button.
TEMP OVER ● The temperature is too high. ● Set this unit to the stand-by mode and wait for a while.
TOC ERR ∗
( ∗ :Number or
symbol)
● The disc is damaged.
● TOC information cannot be read.
● MD not specified.
● Replace it with another disc.
TOC FULL ∗
( ∗ :Number or
symbol)
● There is no space left for recording character information
(track names, disc names, etc.). ● Replace it with another recordable disc.
TOC W ERROR ● Recording is impossible. ● Contact the shop where you purchased the unit.
TRAY ERROR ● The CD tray operates incorrectly. ● Unplug the AC power lead, plug it back, and then turn
the power on.
U TOC ERR ∗
( ∗ :Symbol)
● TOC information recorded on the MD does not match
the MD specifications or it cannot be read. ● Replace it with another disc.
● Erase all of the track, and try recording.
U TOC W ERR ● The TOC information could not be created properly due
to a mechanical shock or to scratches on the disc. ● Set this unit to the stand-by mode and try to write the
TOC again.
(Remove any source of shock or vibration whilst writing.)
? DISC ● The data contains an error. ● Replace it with another disc.
00:00 ● Music is not being recorded. ● Replace the disc with another recordable disc.
MD-X60H(SUK) TINSE0227AWZZ
53