Sharp MD-X60H User Manual
Page 51
YO
MINIDISC SYSTEM LIMITATIONS
Even if the maximum recording time of a MiniDisc has not
been reached, "TOC FULL" may be displayed.
Even if the maximum recording time of a MiniDisc has not
been reached, "DISC FULL" may be displayed.
Even if several short tracks are erased, the remaining rec-
ording time may not show an increase.
Two tracks may not be combined in editing.
The total of the recorded time and time remaining on a
disc may not add up to the maximum possible recording
time.
If recorded tracks are fast reversed or fast forwarded, the
sound may skip.
In the MD system, the delimiter of the recording area on an MD is programmed
in a TOC. If partial erasing, recording and editing are repeated several times,
TOC information will fill up, even though the number of tracks has not reached
the limit (255 tracks), and further recording will be impossible. (If you use the all
erase function, this MD can be used from the beginning.)
If there is any flaw on the MiniDisc, that part is automatically excluded from the
space available for recording. Therefore, the recording time becomes shorter.
When the remaining recording time of a disc is displayed, short tracks less than
12 seconds long may not be included in the total.
For MiniDiscs on which repeated recording and editing operations were per-
formed, the COMBINE function may not work.
A track recorded from a CD (digital recording) and a track recorded from a radio
or other equipment (analogue recording) cannot be combined.
A cluster (about 2 seconds) is normally the minimum unit of recording. So, even
if a track is less than 2 seconds long, it will use about 2 seconds of space on
the disc. Therefore, the time actually available for recording may be less than
the remaining time displayed.
If there are scratches on discs, those sections will be automatically avoided (no
recording will be placed in those sections). Therefore, the recording time will be
reduced.
An MD which has been recorded or edited repeatedly may skip during fast reverse
or fast forward.
TROUBLESHOOTING
■
If a problem occurs
If this unit functions abnormally during operation, first check the following items. If the unit continues to function abnormally, or if an abnormality
appears other than listed below, set this unit to the stnad-by mode and disconnect the AC power plug, then consult your SHARP dealer or service
personnel.
General
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
The clock is wrong.
●
Did a power failure occur?
●
Try setting it again.
●
When a button is pressed, the unit does
not respond.
●
Set this unit to the stand-by mode and then
turn it back on. Then, retry the operation.
●
No sound is heard.
●
Is the volume level is set to "0"?
●
Are the headphones connected?
●
Are the speaker wires disconnected?
●
Increase the volume level.
●
Disconnect the headphones.
●
Connect the wires securely.
●
Radios make unusual noise or the picture
on the TV screen is distorted.
●
When a radio or TV which uses an indoor
aerial is placed near the unit, the picture on
the TV screen may be distorted or the radio
may not function properly.
●
It is recommended that you use an external
aerial.
CD playback
SYMPTOM
POSSIBLE CAUSE
REMEDY
●
Even though a disc has been loaded, "NO
DISC" or "ERR" is displayed.
●
Playback stops in the middle of a track, or
playback is not performed properly.
●
Playback sounds are skipped.
●
The disc is loaded up-side down.
●
The disc is very dirty.
●
The disc which does not satisfy the stand-
ards.
●
Is the unit located near excessive vibra-
tions?
●
Has condensation formed inside the unit?
●
Load the disc with the correct side up.
●
Clean the disc.
●
Load the correct disc.
●
Place the unit on a firm, level surface free
from vibration.
●
Remove the disc and leave the power
turned on. The unit should function properly
in about 1 hour.
MD-X60H(SUK) TINSE0227AWZZ
50