JVC RX-1024VBK - Manual (Page 63)

60
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC video components through the AV COMPU LINK
jacks (see page 56) in addition to the connections using cables with RCA pin
plugs (see pages 9 to 10) or using a digital cable (see page 11).
• When using the remote control:
– For the DVD player and the VCR: Aim the remote control directly at the
remote sensor on the each component.
– For the TV having AV COMPU LINK terminal “RECEIVER/AMP”: Aim the
remote control directly at the remote sensor on the receiver when operating the
TV.
– For the TV having AV COMPU LINK terminal “AV COMPU LINK EX”: Aim
the remote control directly at the remote sensor on the TV when operating the
TV.
VCR1 (the VCR connected to the VCR1 jacks)
You can always perform the following operations (with the
remote control mode selector set to “AUDIO/TV/VCR”):
VCR1 POWER:
Turns on or off the VCR1.
After pressing VCR1 or VCR1 CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can
perform the following operations on the VCR:
PLAY:
Starts playing.
REW: Rewinds a tape.
FF: Fast winds a tape.
STOP: Stops operations.
PAUSE: Pauses playing or recording temporarily. To
release it, press the PLAY button.
REC
¶ ¶ ¶ ¶ ¶:
Press this button with the PLAY button to
start recording.
Press this button with the PAUSE button to
enter recording pause.
CHANNEL +/–: Changes the channels on the VCR.
1 – 9, 0:
Selects the channels on the VCR.
For channel 5, press 5.
For channel 10, press 1, then 0.
DVD player
After pressing DVD (with the remote control mode selector set
to “AUDIO/TV/VCR”), you can perform the following
operations on a DVD player:
PLAY:
Starts playing.
4 4 4 4 4:
Returns to the beginning of the current (or
previous) track.
¢ ¢ ¢ ¢ ¢:
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Stops playing temporarily. To release it, press the
PLAY button.
After pressing DVD (with the
remote control mode selector
set to the “AUDIO/TV/VCR”
position), these buttons can
be used for the DVD menu
operations.
Note:
For detailed menu operations,
refer to the instructions
supplied with the discs or the
DVD player.
Notes:
• Some JVC VCRs can accept
two types of the control
signals – code “A” and “B.”
Before using this remote
control, make sure that the
remote control code of the
VCR1 is set to code “A.”
• You can use either the VCR1
button or the VCR1
CONTROL button to activate
the buttons listed to the left. If
you press VCR1, the playing
source also changes. On the
other hand, if you press VCR1
CONTROL, the playing source
does not change.
TV/CATV/
DBS VCR 1
POWER
VCR 1 VCR 2 VIDEO
CD TAPE/MD PHONO TV/DBS
AM
MODE
SURROUND CNTR TONE CNTR – +
DIGITAL/
ANALOG
INPUT
CHANNEL – +
VOLUME – +
DISC
MUTE
+10
100+
10
FM
1
SLEEP
POWER POWER
AUDIO
2 3
TEST REAR · L
AUDIO/
TV/VCR
CATV
DBS
REAR · R
– +
4 5 6
EFFECT
SEA MODE
RETURN FM MODE/
MUTE
– +
SUBWOOFER – +
8
0
9
ENTER
MENU
MENU
SET EXIT
VCR1
/REW PLAY
TAPE
ON SCREEN CONTROL
CONTROL
LIGHT
FF/
DOWN TUNING UP
TV/VIDEO
REC
STOP PAUSE
RM-SR1024U REMOTE CONTROL
SOUND
DVD
7 /P
CNTR – +
2 3
TEST REAR · L
REAR · R
– +
4 5 6
– +
8
ENTER
MENU
EN56_70.RX-1024V[J]/1.PM5 98.5.12, 0:44 PM 60