Ingersoll-Rand ARO PD15P-X - Manual

E
2010 CCN 15197205
(800) 276-4658 D FAX (800) 266-7016
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
1-1/2” DIAPHRAGM PUMP
OPERATOR’S MANUAL PD15P-X
RELEASED: 9-5-03
REVISED: 5-12-10
(REV. 12)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
1:1 RATIO (NON-METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
PE15P-X
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637389 for air section repair (see page 6).
637391-XX for fluid section repair (see page 4). NOTE: This kit also con-
tains several air motor seals which will need to be replaced.
637390-X major air valve assembly (see page 7).
PUMP DATA
Models see Model Description Chart for “-XXX”. . . . . . . . . . .
Pump Type Non-Metallic Air Operated Double Diaphragm . . . . . . .
Material see Model Description Chart. . . . . . . . . . .
Weight PX15P-FKS-XXX 63.94 lbs (29.00 kgs) . . . . . . . . . .
PX15P-FPS-XXX 42.60 lbs (19.32 kgs) . . . . . . .
PX15P-YKS-XXX 55.94 lbs (25.37 kgs) . . . . . . .
PX15P-YPS-XXX 42.30 lbs (19.19 kgs) . . . . . . .
Maximum Air Inlet Pressure 120 p.s.i.g. (8.3 bar) . . . . . . . . .
Maximum Material Inlet Pressure 10 p.s.i.g. (0.69 bar) . . . . .
Maximum Outlet Pressure 120 p.s.i.g. (8.3 bar) . . . . . . . . . .
Maximum Flow Rate (flooded inlet) 123.1 g.p.m. (465.9 l.p.m.) . . . .
Displacement / Cycle @ 100 p.s.i.g. 0.617 gal. (2.34 lit.) . . .
Maximum Particle Size 1/4” dia. (6.4 mm) . . . . . . . . . . . .
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM -60
_ to 280_ F (-51_ to 138_ C)
. . . . . . . . . . .
Hytrel R -20
_ to 150_ F (-29_ to 66_ C)
. . . . . . . . . . . . . . . .
Nitrile 10 _ to 180_ F (-12_ to 82_ C) . . . . . . . . . . . . . . . . .
Polypropylene 35 _ to 175_ F (2_ to 79_ C) . . . . . . . . . . .
PVDF (Kynar R ) 10 _ to 200_ F (-12_ to 93_ C) . . . . . . . . . .
Santoprene R -40 _ to 225_ F (-40_ to 107_ C) . . . . . . . . . . .
PTFE 40 _ to 225_ F (4_ to 107_ C) . . . . . . . . . . . . . . . . .
Viton R -40
_ to 350_ F (-40_ to 177_ C)
. . . . . . . . . . . . . . . .
Dimensional Data see page 8 . . . . . . . . . . . . . . . .
Mounting Dimension 8.687” x 14.937” (220.7 mm x 379.4 mm) . . .
Noise Level @ 70 p.s.i., 60 c.p.m. 81.0 db(A) { . . . . .
 The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
PX15P-FXS-XXX PX15P-YXS-XXX
MODEL DESCRIPTION CHART
P X 15 P - X X S - X X X
PX15P - XXS - X X X
637391 - X X
Diaphragm Ball
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: Model # PD15P-FPS-PAA
Fluid Section Service Kit # 637391-AA
Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene
M - Medical Grade Santoprene
C - Hytrel T - PTFE / Santoprene
G - Nitrile V - Viton
Hardware Material
S - Stainless Steel
Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene
Fluid Connection / Location
F - 1-1/2” A.N.S.I. / Din Flange / End
Y - 1-1/2” A.N.S.I. / Din Flange / Center
Center Section Material
P - Polypropylene
Ball Material
A - Santoprene
S - 316 Stainless Steel
C - Hytrel T - PTFE
G - Nitrile V - Viton
Electronic Interface
D - None
E - Available
www.ingersollrandproducts.com