Ingersoll-Rand ARO PH10A-X-X - Manual

E 2010 CCN 99755480
(800) 276-4658
D
FAX (800) 266-7016
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
OPERATOR’S MANUAL PH10A-X-X
RELEASED: 7-7-00
REVISED: 10-15-10
(REV. M)
INCLUDING: OPERATION, INSTALLATION & SERVICE
1” HIGH PRESSURE DIAPHRAGM PUMP
3:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to “Model Description Chart” to match the pump material options.
637338 for air section repair (see page 6).
637339 for fluid section repair (models PH10A-XXX-XSX)(see page 4).
637339-1 for fluid section repair (models PH10A-XXX-XHX)(see page 4).
PUMP DATA
Models see “Model Description Chart” for “-XXX”. . . . . . . . . . . .
Pump Type Metallic Air Operated, High Pressure, . . . . . . . .
Double Diaphragm.
Material see “Model Description Chart”. . . . . . . . . . . .
Weight 94.73 lbs (42.97 kg) . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Air Inlet Pressure 100 p.s.i. (6.9 bar) . . . . . . . . .
Maximum Outlet Pressure 300 p.s.i. (20.4 bar) . . . . . . . . . .
Maximum Flow Rate (flooded inlet) 26 g.p.m. (98.4 l.p.m.) . . .
Maximum Particle Size 1/8” dia. (3.2 mm) . . . . . . . . . . . .
Maximum Temperature Limits (diaphragm / ball / seal material)
Nitrile 10_ to 180_ F (-12_ to 82_ C) . . . . . . . . . . . . . . . . .
PTFE 40_ to 225_ F (4_ to 107_ C) . . . . . . . . . . . . . . . . .
Displacement / Cycle @ 100 p.s.i. 0.06 gal. (0.23 lit.) . . . .
Dimensional Data see page 8. . . . . . . . . . . . . . . . .
Noise Level @ 70 p.s.i., 60 c.p.m. 84.5 db(A)j . . . . .
j The pump sound pressure levels published here have been updated to an Equivalent Continuous
Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using fourmicro-
phone locations.
NOTICE: All possible options are shown in the chart. However, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
PH10A-XSS-XXT
1” DIAPHRAGM PUMP Figure 1
MODEL DESCRIPTION CHART
PH10 A - X S S - X X T
Seat Material
H - Hard 440 Stainless Steel
S - 316 Stainless Steel
Ball Material
H - Hard 440 Stainless Steel
S - 316 Stainless Steel
Fluid Caps & Manifold Material
S - Stainless Steel
Fluid Connection
A - 1 - 11-1/2 N.P.T.F. - 1
B - Rp 1 (1 - 11 BSP parallel)
Diaphragm Material
T PTFE
Hardware Material
S - Stainless Steel
Center Section Material
A - Aluminum
www.ingersollrandproducts.com