beautypg.com

Security codes & authority levels, Cont.) – Garmin FA168CPS User Manual

Page 31

background image

– 31 –

Security Codes & Authority Levels

Security Codes & Authority Levels

Security Codes & Authority Levels

Security Codes & Authority Levels

(Cont.)

(Cont.)

(Cont.)

(Cont.)

How to Assign

How to Assign

How to Assign

How to Assign Security

Security

Security

Security Codes and Attributes

Codes and Attributes

Codes and Attributes

Codes and Attributes

The following lists the various command strings for adding security codes and attributes.

Refer to the User Setup chart at the back of this manual for factory

assignments of user attributes and to keep a record of user programming.

NOTE: Partition Master codes (FA168CPS only) apply only to those user numbers

previously assigned (by the system master/installer) to the partition master’s partition.

Add Security Code:

System/Partition Master code + [8] + user no.

+

new user’s security code

(Users 03/33 are preset

User 01 = installer

User 03 = partition 1 master

to partition programmers,

User 02 = master

User 33 = partition 2 master

but can be changed.)

The Keypad beeps once to confirm that new user was added.

Delete Security Code:

System/Partition Master code + [8] + [user no.] + [#] [0]

The user code and all attributes* programmed for this user number,
including any associated RF keys, are erased from the system.
(*except assigned partition)

Authority Level:

System/Partition Master code + [8] + [user no.] + [#] [1]+ auth. level

Factory Assignments:

Authority Levels (see definitions on previous page):

users 04-32/34-49 = 0

0 = standard user

3 = duress

users 03/33 = 4

1 = arm only

4 = partition master (FA168CPS only)

2 = guest

Access Group:

System/Partition Master Code + [8] + [user no.] + [#] [2]+ group (1-8)

Factory Assignments: none

You can assign users to a group, then set an access schedule that
defines the times this group of users can operate the system. The
system ignores these users outside the scheduled times.

User’s Partition:

System Master Code + [8] + [user no.] + [#] [3] + [0] + partition(s) + [#]

(FA168CPS only)

This command assigns the partitions the user can access. If more

Factory Assignments:

than one, enter partition numbers sequentially, then press [#] to end.

Part. 1 = users 03-32

E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#] gives

Part. 2 = users 33-49

the user access to partitions 1 and 2 and the common partition.

Partition Entries: 1 = partition 1 and common

2 = partition 2 and common

3 = common partition only

RF User Number:

Master/Part. Prog. Code + [8] + [user no.] + [#] [4]+ zone no.

Factory Assignments: none

Use this command to assign a wireless button device (keyfob) to this
user (keyfob must be enrolled in system first; see installer).

Z

one number: enter the zone number assigned to a button on the

keyfob that will be used for arming/disarming by this user.

Pager On/Off:

Master/Part. Prog. Code + [8] + [user no.] + [#] [5] + 0 or 1

Factory Assignments:

Y

ou can program a user so that a message is sent to a pager

users 01-49 = 1 (on)

whenever this code is used to arm or disarm the system.

Paging On/Off: 1 = allow paging; 0 = no paging for this user