beautypg.com

3 cooling and ventilating air, Danger, 5 compartment floor cutouts – Guardian Technologies QUIETPACT 40LP 004701-0 User Manual

Page 25: 1 generator airflow, All measurements are in millimeters, 25.4 mm = 1, Recreational vehicle generator, View from top, Connections in back of generator

background image

2.2.5 coMpartMent Floor cutouts

Provide openings in the generator compartment for

the following items (Figure 2.7):
• Engine exhaust and cooling air outlets
• Generator cooling air inlet
• Four holes for passage of generator mounting

bolts. See Section 2.1.4.

danger

Fuel lines and exhaust piping must not pen-

etrate into the vehicle living area.

2.3 coolIng and ventIlatIng aIr

It is absolutely essential that an adequate flow of

air for cooling, ventilating and engine combustion

be supplied to the generator set. Without sufficient

airflow, the engine/generator quickly overheats. Such

overheating can cause serious operating difficulties

and also may cause fire and personal injury. The

installer must make sure that sufficient air is avail-

able to the generator for cooling, ventilating and

combustion. The installer also must provide for a

path for exhausting the cooling air to the exterior of a

compartment, if so equipped.

danger

Never use discharged cooling air for heating or

permit such air to enter the vehicle interior. This

air contains deadly carbon monoxide gas and

other poisonous, flammable or explosive gases.

2.3.1 generator aIrFlow

Engine operation drives cooling fans for the two-stage

cooling air system. A pressure fan draws cooling air

into the bottom right side of the generator (Figure

2.8). This airflow cools the engine/generator and elec-

tronic components. The second part of the cooling

system, a suction fan, draws air that is heated from

a hot engine into a collector compartment at the left

side of the unit. This heated air (although cooler than

exhaust muffler) is then deflected out the bottom

toward the ground.

section 2 – Installation

recreational vehicle generator

Figure 2.7 – Compartment Floor Cutout (Drawing 0F4610)

342.2

[13 1/2"]

778.9

[30 11/16"]

REF.

FRONT DOOR ACCESS FOR
ALL REQUIRED MAINTENANCE

REMOTE PANEL
CONNECTOR

500.2

[19 11/16"]

REF.

AC OUTPUT
HARNESS

HOT AIR

EXHAUST

TAIL PIPE

EXIT

OIL DRAIN

AIR

INTAKE

48.1

[1 7/8"]

222.7

[8 3/4"]

300.7

[11 13/16"]

369.7

[14 9/16"]

688.3

[27 1/8"]

29

[1 1/8"]

55.5

[2 3/16"]

376.5

[14 13/16"]

5/16"-18 WELDNUTS
(6 PLACES)

82.5

[3 1/4"]

343.4

[13 1/2"]

423.2

[16 11/16"]

717.7

[28 1/4"]

50.8

[2"]

118

[4 5/8"]

223.5

[8 13/16"]

60

[2 3/8"]

210

[8 1/4"]

176.6

[6 15/16"]

83.5

[3 5/16"]

429.5

[16 15/16"]

414.5

[16 5/16"]

360.5

[14 3/16"]

63.5

[2 1/2"]

416

[16 3/8"]

170

[6 11/16"]

79

[3 1/8"]

101

[4"]

TYP.

6.7

[1/4"]

736.4

[29"]

476.4

[18 3/4"]

36.5

[1 7/16"]

[1 7/16

[1 7/16

39.6

[1 9/16"]

69.6

[2 3/4"]

34.3

[1 3/8"]

71.2

[2 13/16"]

211.3

[8 5/16"]

NEG. BAT.
CONNECTION

POS. BAT.
CONNECTION

LP FUEL INLET

VIEW FROM TOP

NOTE: ALL AIR INTAKES AND EXHAUST OUTLETS MUST BE
KEPT CLEAR OF ANY OBSTRUCTIONS. ALL OPEN AREA
IS REQUIRED FOR COOLING.

CONNECTIONS IN
BACK OF GENERATOR

All measurements are in millimeters, 25.4 mm = 1”.