Warning messages, D-108 owner's manual (names and functions), Invalid data indication – Fostex D-108 User Manual
Page 21: Action to take, Invalid in/out indication, Overtime indication, Unassigned track indication, Event overflow indication, Load error indication, Un-formatted indication
D-108 Owner's Manual (Names and Functions)
21
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
8
7
6
5
4
3
2
1
42
OL
0
30
24
18
12
9
6
3
∞
6. Warning messages
If you perform an incorrect operation, input incorrect data, or if an error occurs, the following alarm indication appears:
Invalid data indication:
The input data is not appropriate
for the operation.
Action to take:
Input correct data.
Invalid In/Out indication:
The In or Out point is not
appropriate for the operation.
Action to take:
Input correct data.
Overtime indication:
Available disk space is insufficient
for the length of time (the number of measures) indicated
on the display.)
Action to take:
During the copy & paste and move & paste
operation, try to shorten the length of the copied data by
the indicated amount. Alternatively, use the "ERASE"
function to move the ABS END point backward to obtain
enough disk space for editing.
Unassigned track indication:
Select any track.
Action to take:
Use the RECORD TRACK select key to ready
any track.
Event overflow indication:
The editing points are
overflowed.
Action to take:
You edited too much. The warning means
"you cannot paste or erase any more." In regards to event,
refer to "Event and Audio File" in "Before Starting" section.
Load error indication:
You cannot load data because the
data input to the DATA INPUT connector contains an error.
Action to take:
Check to see if there is an abnormality
with the external digital machine connected to the DATA
INPUT connector, or cable. Try to "LOAD" again.
Un-formatted indication:
The internal hard disk is
damaged or not formatted yet. After this message is shown
for about 10 seconds, "Disk Format ?" in Setup mode will
flash on the display.
Action to take:
Press and hold down the RECORD button
and press the EXECUTE/YES key to format the disk. (All
audio and other data on the disk will be lost.)
Disk error indication:
This disk cannot be read.
Action to take:
Contact the Fostex service station as soon
as possible.
Recording Disable:
Recording is disabled.
Action to take:
Change the "Off" (recording) "Rec Protect
?" setting in Setup mode.
Hard disk (E-IDE or SCSI) connection error:
The hard disk is not connected correctly.
Action to take:
Check to see if the external SCSI device is
connected to the SCSI connector correctly, or the power to
the SCSI device is turned on.