Fostex D-108 - Manual (Page 15)

D-108 Owner's Manual (Names and Functions)
15
34. Locate key [LOCATE]
Use this key to start to start the LOCATE feature.
Pressing this key after a memory key (CLIPBOARD IN/
OUT, AUTO RTN START/END, AUTO PUNCH IN/OUT)
locates the memory data programmed in each respective
key (time mode or bar, beat, clock setting).
The data can be programmed by individually setting it
with one of the 99 (01-99) LOCATE numbers of the
LOCATE key.
Note that the data of memory number 00 is available in
addition to LOCATE numbers 01-99. The last LOCATE
time setting (bar, beat, clock setting) constantly replaces
the data stored in the LOCATE key as data in memory
number 00. Therefore, it is possible to press this key
alone to repeatedly LOCATE the same point.
These data can be individually stored in programs P1-
P99. The data for each program is SAVED or LOADED for
each program when the song data is designated for SAVE/
LOAD in the SETUP mode. This data is maintained even
when the power is turned OFF.
* Refer to page "60" for more information about the Locate
function.
35. Record button [RECORD]
Pressing only this button places the readied tracks into
input monitoring status. Pressing this button again will
reset the tracks to playback monitoring. (The RECORD
LED will blink when the readied tracks are in input
monitoring status.)
Pressing the PLAY button while holding down this button
will place the readied tracks into recording. At this time,
the PLAY LED and RECORD LED will light, and the readied
track indication will be light steadily (instead of blinking).
* Refer to page "26" of the "Before Operating" section for more
information about input monitoring and reproduce monitoring.
36. Stop button [STOP]
Pressing this button will stop the transport section of the
recorder. Pressing the PLAY, REWIND, or F FWD button
while holding down this button will cause the D-108 to
perform the following operation:
Pressing the STOP button will abort the editing operations
and display the current position of the recorder, if you
wish to:
* quit the data edit mode,
* cancel the recall or store operation,
* quit the pitch data display,
* cancel the edit operation, such as pasting, or
* cancel the SETUP menu settings.
Pressing the foot switch while holding down this button
allows you to turn the punch in/out rehearsal mode ON/
OFF.
*1 Clipboard playback:
The D-108 plays back the copy data or move data for the
Clipboard. During audio playback of the copy or move
data, the FL will display the time length and data type
(“Copy Clip Play!” or “Move Clip Play!"), and the copy or
move source track indicator will flash, enabling you to
quickly determine the track and data type.
*2 Locate ABS 0:
The D-108 will locate the top of the selected Program
(ABS TIME: 00m: 00s: 00f).
*3 Locate REC END:
The D-108 will locate the end of the recorded data on the
Program (ABS REC END).
* These operations can be executed only on real tracks 1 ~ 8.
* Refer to page "22" of the "Before Operating" section for more
information about ABS 0 and ABS END.
* Refer to page "43" for more information about Punch In/Out
recording using the foot switch.
37. Play button [PLAY]
Pressing this button will cause the recorder to play back.
Pressing this button while holding down the RECORD
button will start recording.
Pressing this button while holding down the STOP button
will perform the Clipboard playback operation. Refer to
the section “STOP button” for more information on the
Clipboard playback.
Pressing the PLAY button during recording will stop
recording.
38. Rewind button [REWIND]
Pressing this button while the recorder section is stopped
will rewind data at 30 times speed. Pressing this button
in Play mode will cue data (you can hear sound while
rewinding) at five times speed.
Pressing this button while holding down the STOP button
will perform the "LOCATE ABS 0" operation, and
immediately locate the beginning of the Program (ABS
TIME: 00m: 00s: 00f). (Refer to the "STOP button" section
for more information about LOCATE ABS 0.)
STOP button + PLAY button
STOP button + REWIND button
STOP button + F FWD button
Clipboard playback (The STOP LED will flash and
the PLAY LED will light up.) *1
Locate ABS 0 *2
Locate REC END *3
Pressing the RECORD TRACK select key while holding
down the STOP button will cause the envelope function
to start, thus, you to use the JOG dial to digital scrub of
the track selected.